How to open a systemist. We disassemble the system block of the computer. Connect hard drives and drives

We decided to implement a wonderful idea - Want to construct a gas furnace with your own hands for cauldron, bread, firing ceramics or with an oven? It is not necessary to consider it as a problem is a certain task, the implementation of which forces to everyone. Many doubt and think that it is unrealistic and afraid to face the difficulties that may occur in the process.

The undoubted advantage that the gas furnace has a gas furnace for heating at home and kitchen with an oven or cauldron is the ability to use various options for the base. To date, the popularity of gas furnaces for kitchen, cauldron or firing ceramics at the proper level and even more than this. The fact is that this equipment You can use not only for the heating of your private dwelling, but for cooking, if there is an oven, it will be difficult to abandon bread, cooked with their own hands.

Before starting the installation work on the installation of the oven with your own hands it is necessary to determine the type of fuel.which will be used in the future. As the basis of the workflow is better take natural gas, in mind its cheapness and availability. Economic parameters of such a furnace explain its wide popularity.

Oven with oven for gas for cauldron and bread and its features

In most cases, a portable oven is a basic competitor among existing heat sources and structures for firing and cauldron. It is difficult to compare this functional device with or any other solid and liquid fuel.

Simplicity is the main difference between this unit during operation. In the warm time it will take for warming up no more than 2 hoursAnd in the winter to obtain the desired temperature will be spent a maximum of 4-5 hours.

For kitchen subway, certain rules related to the process of mounting the boiler must be observed. Approximate time exploitation is not much not enough - about 25 years old, and if preventive and repair work will be carried out in a timely manner, the furnace will last, at a minimum, twice. Surely for each such perspectives show tempting. It is possible to use the finished analogues - the electrophum, of course, but it is unlikely to achieve a characteristic flavor of fresh bread, it is hardly possible.

Constructive features

If you represent the visually elements that make up the basis of a portable underground kitchen oven with an oven, which works on firewood or any other liquid and solid fuel, then the design of the gas furnace to understand can not every. This requires certain skills and experience. But this is not a problem - it is necessary to understand the features. Gas portable oven for heating at home, kitchen or baking bread, includes the following items:

• Protective housing that allows exclude excitement for internal content.
• Fuse providing termination of gas supply in case of attenuation. It should be noted that the system with the use of firewood does not have such an opportunity.
• Responsible for thermal properties - thermostat.
• Sealed furnace chamber, which depends on its integrity. In the process of choice and acquisition, you need to trace it clearly.
• Chimney - Part of the structure that provides the removal of combustion products. In addition, ON. also is the source of heat.

See also: Long burning ovens with water contour

We collect a gas burner with your own hands

For example, consider the possibility of making an infrared muffle furnace for a kitchen and bread baking with your own hands, which will work on gas. This option can be used even for melting various metals, roasting or cauldronsince the temperature of the firing can reach 1400 degree marks.

The base of the furnace is the case and burner. To make a gas burner, you will need a small piece of pipe having diameter no more than 2 cm, and about 15 cm long. From the side of the external thread, you will need to drill a certain number of holes, the first of which ( from the edge of the pipe) Must be through. It is necessary for placement of gas supply tube.

The following three holes must be removed from the edge. Their main purpose is a tellek tier and an air fence. The through hole used for the gas supply tube must be clear perpendicular to three holes. A copper pipe is used for a gas pump tube, the diameter of which is approximately 0.8 cm. In both ends, a thread should be present, and in the center - non-cutnecessary to allow gas. On the thread on one side, the plug is screwed using fumen. On the other hand, there is a corner with outdoor and internal threadto which the hose in the future is joined running from the gas cylinder.

To avoid turning the tube supplying gas in the burner, it is necessary to make a small sleep with a side, which is necessary for fixing the burner with a protracted bolt. An important point is connecting the gas hose and the burner of the subsidence, it is necessary to install the flapreggle valve to achieve complete safety.

Benefits of the sub boot furnace

This infrared design for the kitchen, cauldron, bread baking or firing ceramics has a number of advantages that allocate and affect wide popularity, in contrast to the electrical model.

See also: Furnaces of long burning on solid fuel

The most important positive qualities that possess gas stoves for cottages and cauldronis economy, even if you use a cylinder. This is due to a relatively low gas cost and its availability.

You can save significant funds to maintain a litter on gas, if you compare electrical or solid fuel model. Equipment that works on gas does not require excess of attention and fairly easy to use, unlike the electrical model. Sozha and ash in such an apparatus is practically absent, chimney and the furnace practically do not need cleaning. There is no longer anything about the longevity, since it is difficult to find analog By time of operation.

Features of use

Despite enough hard conditions related to gas applications in everyday life, Furnaces for firing ceramics that work on this fuel are widespread and are safe. The main feature is functionality and small costs in the process of use. In addition, such devices are more environmentally friendly than wood counterparts.

Thanks to this equipment, the room warms up as quickly as possible, And the degree of heat detection depends on the time of year and the temperature "overboard". Due to the quality and uniform warming is achieved comfortable conditions in any room.

A gas portable oven for the bath is practically no different on the device from similar devices, but still have a number of features. First of all, it concerns the type of fuel used. In such devices, in addition to the thermostat, a fuse is required, which is triggered at the moment of attenuation of the burner - the gas is stopped. Camera for burning fuel is located directly under KamenkaThat allows you to ensure rapid string of stones.

For gas firing devices, as well as chimney, chimney is needed, for removal of combustion products. Such furnaces provide the best pairs in the bath, quick heating and the steam room. Due to the uniform distribution of heat stable temperature is ensured.

It is difficult to imagine the full work of any bakery or confectionery production without the use of such equipment as rotary or underground furnaces. Such rotary furnaces can be tunnel and sub-shows, differing in the nature of the activity, are economical and convenient to manage, which allows you to cope with large volumes. - These are devices that have programmable modes of operation. Modern technologies allowed to implement a convenient digital panel, thanks to which the operator has the ability to install the necessary operation of the bread baking operation.

Such an infrared portable furnace can be both gas and electric (heating occurs due to thene or burner). Rotary furnaces are quite economical, and automatic system with understandable and comfortable touchpad Allows you to set the start of work at a specific time. Existing locks greatly facilitate the workflow and allow you to avoid unpleasant moments.

What distinguishes the Russian bath from Turkish Hamam or Finnish sauna? The furnace, which is not just a heating device, but the real heart. It is the opinion that it must be necessarily a Kamenka, but if there is a connection to gas (trunk or balloon), then the bath oven for gas is perfectly cope with fast heating of a large volume of water. Such an aggregate is easy by weight, it is convenient to operate, does not require regular cleaning of the gas pipeline, words, a real find for bath procedures.

Among the additional advantages of the equipment is rapid premises, efficiency, which is especially relevant in the winter season and relative simplicity of manufacture. Currently, the store assortment of heating equipment is quite wide, as well as the pricing policy, but if necessary, we will tell you how to make a stove for a bath on Gaza with your own hands.

The total cost of such a gas furnace directly depends on what material is built. The highest quality and efficient is a brick oven with a built-in inflatable burner, a metal - an economariant, which is also appropriate to bind bricks.

Constructive features

A gas furnace is constructively largely identical to the usual boiler, but differs in quality characteristics associated with the features of the gas. Thus, a fuse is necessarily provided, which stops supplying the fuel at the time of the burner, absolutely hermetic gas chamber. But the fundamental difference is still in the supply of fuel - if the fuel is loaded into the chamber into the solid fuel furnace, then it comes directly from the gas pipeline.

For the safest operation, gas cylinders are always placed outside the building in a special container or bunker placed under the ground.

How to calculate the consumption of natural and liquefied gas

The main indicator on which the calculation depends is the area of \u200b\u200bthe room and the power consumption of the equipment. Also, street temperature indicators are taken into account during the coldest time.

The calculated indicator ideally is always 35-50% higher than the actual consumed, since the air temperature always changes in a large or smaller side. When choosing finished equipment, this fact should be taken into account and instead, for example, 100 W energy can be taken 50.

The calculation of the amount of natural gas is made by the formula:

L \u003d Q / (QH x 0.92),

• L is the calculated fuel volume (1 cubic meters per hour);
• Q is the power of heating, kW;
• qN is the limiting power of fuel combustion, for natural gas 10.175 kW / m 3;
• 0.92 - Gas boiler / furnace efficiency.

On average, for heating the room with an area of \u200b\u200b100 sq.m. The calculation will look like this:

5 / (10.175 x 0.92) \u003d 0.53 m 3 / h,

what corresponds to the flow rate of natural gas per unit of time (hour).

Based on such indicators, it is possible to determine the nominal gas consumption in any room for a certain period of time. Since the bath is not operated daily and not around the clock, such a flow will be less.

Balloon (liquefied) gas is more expensive and to calculate its flow rate will not have in liters, like natural, but by kilograms. The heat of combustion of gas remains the same - 10.175 kW / m 3 \u003d 12.8 kW / kg, heating power - 5. We get:

5 / (12.8 x 0.92) \u003d 0.42 kg / h,

what corresponds to 0.78 l per hour. Considering that 1 liter of balloon gas weighs 540 mg. Based on the approximate number of days and hours of operation of the bath, you can calculate the required volume.

In order to make a stove for a bath on Gaza with your own hands, you should decide on the three main parameters:

• Material;
• What will be the gas burner;
• Placing the container - a built-in or remote tank.

Now about each of them in more detail.

What materials apply

As mentioned earlier, it is recommended to use chamotte (refractory) brick, metal or stone to manufacture a furnace for a bath on a gas. Stone furnaces melts much longer (4-5 hours), but the temperature is kept for 3-4 hours longer than metallic. Bricks are characterized by similar indicators. In turn, metal aggregates are faster than (placing up to 50 sq.m. fully heated in 2.5-3 hours /), but also cooled faster.

At the same time, metal furnaces are easier for brick analogs and make it easier to produce them, and if it is uninstalled by chammatory brick outside, there will be no fundamental difference between 2 units.

Gas-burners

There are 2 basic types of burners - atmospheric and inflatable.

The first option is the easiest, for which you do not need automatic control and appropriate equipment. With such an atmospheric, the intensity of the fire is maintained by air entering the doors to the chamber, respectively, the efficiency of heating directly depends on the amount of incoming air.

The operation of the inflatable burner provides a blowing fan, forcibly catching up the air into the chamber and also supports the operation of the burner. Given the fact that the fan runs from the power grid, the heating unit is volatile, it means more expensive.

A similar fan is installed in solid fuel, combined and pyrolysis boilers. About, you will learn in the relevant article.

Water tank location

By analogy with traditional baths for the bath on gas equipment, water tank can be built-in, removable or remote, that is, located in another room. In the built-in much faster, water is heated, which contributes to the combustion products in Kamenka.

To heat the water in the remote tank, which can be mounted in the same room or directly in the steam room, a pipe system is used.

How to make a gas oven for the bath do it yourself

To install the gas furnace and its connection it is necessary to obtain permission. The technical conditions and procedure for connecting in each region must be coordinated with the Gorgaz services.

This article discusses the manufacture of a brick gas oven with a burner. Despite the seeming difficulty, it is possible to make such equipment, it is necessary to comply with building technologies and production procedure.

Preparatory process

The main issue of the design is the location of the future furnace. The optimal place will be mounted on 2 rooms so as to make all the rooms, including where people rest. The power of the furnace is enough to heat up the 3 mains - the steam room, a washing and pre-banker.

Necessary materials:

• chamotte brick;
• galvanized steel sheet;
• armature;
• tube, grate;
• clay and sand;
• 2 doors pissed and furnaces;
• base,
• chimney pipe;
• mineral wool for isolation,
• kamenka,
• burner (atmospheric or inflatable),
• heat resistant steel sheet
• decorative lining,
• automatic control unit for burner with inflammatory.

Video 2 Making a brick furnace for a bath

Foundation

Before the construction of the furnace immediately, the proper foundation should be made:

1. Eat the foundation half meter below the freezing level.
2. Fall asleep on the bottom of the sand with a thickness of 20 cm - this is an airbag that reduces the risk of portage of the soil. Sand floors abundantly water, top layer of broken brick or construction debris for 20-25 cm.
3. Fall asleep by 10-15 cm rubble and start formwork. Be sure to make a reinforced frame! Pour concrete from cement, rubble, sand (in equal parts) and water (1/2 volume).
4. Formwork emerging ambassadors, remove the wooden frame (as an option - the formwork can be non-removable) and cover the entire surface of the 2-3 layers of the Hudron (you can use Ruberoid).

Walls of the furnace

Be sure to set the protective wall that will exclude the risk of fire fire. For its manufacture, it is fashionable to use the rifle brick (halfway), laid on the sand-clay solution.

The solution is prepared at the rate of 1 part of the clay and 1 part of river sand.

For laying the base of the furnace, bricks are completely immersed in cold water for several minutes, after which there are still humid on the solution on a bitumen base (waterproofing). The distance between the bricks should vary within 3-5 mm. All subsequent ranks are laid out in a checker order.

In the 3rd row embedding the door pissed. Bashed to the base of it better than steel stripes.

In the 4th row you make a well for a grate grid. In bricks, cut small holes (0.5 cm on each side) so that the place for the temperature expansion of the metal remains.

Installation of fittings

• In the 6th row also on steel bands pinning the door for pondered.
• In the 7th - grate grid.
• 8th - installation of the partition for the construction of the chimney pipe.
• 14 - Cutting channels for tank. To do this, it is necessary to make a deepening, where the tank will later "enter".
• From the 15th row of bricks are superimposed for the manufacture of the distribution wall. From 15 to 18 rows, the loop is reduced.
• In the 19th row, the door is installed for the release of unnecessary vapors.
• In the 20-21-m - stripes for the built-in capacity, which must also be postponed with bricks.
• From the 23rd row, start laying the chimney, the size of which is selected from the size of the room of the bath. From the side of the street, the pipe is necessarily isolated by mineral wool and its height is 1 meter over the ridge of the roof.

Minimal thickness The chimney must be at least ½ brick thickness.

For street laying, the base under the chimney is recommended to use a concrete solution to eliminate its breaking by precipitation.

The final stage

After the furnace laying is complete, it must be stuck. This is performed not only from decorative motives, but also to improve thermal insulation properties. For plastering, you can use any available solution where to add at least a quarter of the volume of alabaster. It will qualitatively improve the finish and allow materials to "breathe."

In the absence of alabaster, it is possible to use gypsum, but at the same time prepare a solution with small portions. Compared to the alabaster, the gypsum grasps 2 times faster.

• Choosing between the main gas pipeline and balloon gas, consider that the latter has a higher thermal power factor. Recall once again that the gas cylinder must be kept outside of the room, preferably buried in the box under the ground.
• Be sure to use the automatic unit for the gas boiler. This is necessary to stop the supply of fuel when any emergency occur.
• The furnace for a bath on Gas self-made, which was discussed in the article, can be launched after 14-20 days depending on the ambient temperature. It is not recommended when starting starting to bring it to full heating.
• Be sure to use iron barriers between the wall and the heating unit and in front of it to eliminate the risk of spontaneous ignition.
• Chimney labor is always made of stainless steel.
• The maximum distance from the gas burner to the end of the chimney pipe is within 5 meters.
• In the room where the gas stove is installed for the bath, with their own hands, or with the help of specialists it is necessary to provide high-quality ventilation.

And here you will learn what the ovens differ from each other, and which it is better to choose in the ready version.

Video 3 than one bath oven differs from another

In general, we note that the gas stove for the bath optimal option. Quickly overalls the room, it holds a temperature for a long time, economical in operation, there is no need for frequent cleaning of the chimney. But only this type of heating equipment, subject to connecting to the main line, requires a number of agreed actions for subsequent operation.

1.
2.
3.
4.

As for heating, it is necessary to conceive many owners of private and country houses. From how correctly the heating device is chosen and the heat supply system itself, comfort in the house depends. Today, the most popular is the simple gas stove for the house very in demand. And how effective it will be effective depends on which the gas furnace is selected for home heating. What do these devices look like, you can look at the photo.

In the process of operation of the gas furnace, the lattice is heating, and the heat enters the walls of the fuel. This ensures uniform heating of air. If you install gas burners in the fifth system at the lower level, the lower laying of the furnace will become more efficient to warm up, and accordingly, the volume of the fuel will be used as reasonable.

The fuel furnace fuel in the upper part borders with smokers, and in the lower area, it communicates with pensions. Through this element in the gas stoves for the house enters air, without which the combustion of fuel becomes impossible.

The flue gases entering the text of the thrust from the fuel, give the chimney heat. Gas furnaces for the house have a design that gases pass through the channels connected in a sequential order. These channels have no more than five smoke revolutions. Gas furnaces are strictly prohibited to install in homes in which there is a horizontal location of the channels. Like firewood boilers, gas devices should be located at some distance from the walls.

Furniture gas heating: types

From how the burner is used, the power, efficiency, efficiency and safety of the furnace depends. In it, the gas is mixed with oxygen.

The burners are several types depending on the type of power management:

• single-stage products (fuel supply or turned on or turned off);
• two-stage (the furnace can go into the savings mode, which reduces the heat of heating);
• floating adjustment (power changes smoothly).

By type of air supply burners there are:

• atmospheric (air sunsited by means of thrust), they do not depend on electricity, but the efficiency does not exceed 90%;
• advanced (the air is fed with a fan with a closed chamber), they depend on electricity, and efficiency exceeds 95%.

Also, burners can be either with an electric ignition, or with Pierorozhig. The first depend on electricity, but there is no constantly burning stamp. See also: "".

Gas stove for home: Benefits

The use of gas furnaces for the house has the following advantages:

1. Ability to operate at any time of the year and day. In heating systems of this type there is no interruptions.
2. High efficiency. Gas stoves help create a comfortable temperature in the house at any temperature on the street, even in a heavy frost. Unlike solid fuel boilers, for gas units is not required for storing fuel, and natural gas is a relatively cheap flammable.
3. Easy operation. The oven gas heating is very convenient, the cost of maintaining the heating system is minimized (read also: "").
4. Durability. Gas furnaces are durable - they serve several decades, therefore the likelihood that they will fail for the next 10 years, minimized.

Of course, gas units have some drawbacks, but compared to other heating devices, they are much smaller. The most significant is the high price of gas equipment, but given the low cost of fuel, with time the acquisition is completely paid off. If you use ovens working on other types of fuel, heating costs will be several times more.

Installing gas furnaces

Connecting gas devices to a centralized gas pipeline will be hidden, not all owners of private houses can afford it. Therefore, if the building is not yet connected to the gas highway, it is worth considering other options for creating heating or buy cylinders (more details: ""). If the gas is already supplied to the site, the device of the heating system will cost much cheaper.

After the gas heat unit was mounted in the house, it is necessary to check the equipment. Any errors in the installation process can adversely affect comfort in the house and the effectiveness of heating. In addition, gas equipment at incorrect installation It may harm a person - natural gas is dangerous fuel, and it is impossible to forget about it. See also: "".

Connecting gas furnaces should be made by experts. After that, it is necessarily checked by the correct installation so that when the heating equipment is launched, unexpected situations occur.

Heating furnace on gas is an effective, durable and economy device. It does not need regular maintenance, but it is important to correctly make installation so that the furnace is safe, and a comfortable temperature was maintained in the house without extra fuel costs.

Modern gas stove for home on video:

The connoisseurs of the Russian bath perfectly know what a bass oven is. It's just her heart. Therefore, the choice should be treated with all seriousness. It is best to do this at the initial stage of construction.

Many prefer to make her own, others are going to buy ready. The aggregates of this type are presented in large quantities in the retail market. If it is possible to use the main gas, it is advisable to install gas stoves for a bath with a heat exchanger for heating water.

Not only quickly warm up the air in the bath, but it is enough to be saturated with warm walls, but it will take much more time for this. And the heated walls are the key to a good bath.

By type of fuel, the furnace can be different species: Working using electricity, wood, solid fuel or gas. About how to choose a stove for a bath, read in the article. Here we will look at what is a gas furnace for a bath equipped with a heat exchanger.

High-quality gas furnaces for a bath with an additional heat exchanger can satisfy the demands of the most avid bayman:

• A modern gas stove for a bath with an additional heat exchanger has enough compact sizesPerhaps even accommodation in small rooms.
• Nowadays, there are many types and modifications to the gas bath on Gaza, possess modern design. She perfectly fit into any interior of the bath.
• Automation that is equipped with a gas furnace for a bath can, without your participation, maintain the specified temperature and humidity.
• Easy operation of the oven for a bath on Gas makes it possible to use the stove even a child.
• The availability of fuel is the permanent supply of gas will allow not to think about purchasing raw materials for the heating of rooms in the bath.
• If desired, the gas furnace for the bath can be installed in the shortest possible time and without additional costs, however, to connect the furnace in the bath, you need to invite a gas service representative.

It should also be noted here that gas furnaces with an additional heat exchanger are produced under any room. A smaller structure will save on costs without reducing the quality of heating. To buy an aggregate, it is not necessary to save much, because the oven will serve not one year. It is worth taking quality products.

Installation rules

Gas can be installed, but some rules should be performed for the installation of such a design:

• The gas pipeline indoors should be made of copper and steel.
• If flexible connections are used when connected, they must be resistant to pressure and temperature.
• Installing flexible sleeves should be made according to current standards. If they are manufactured in other countries, you need to take a certificate for products.
• Flexible connections used to connect the gas must be marked "Gas" and enjoy with a diameter of 10 mm. Sleeves should not have junctions, that is, be solid.
• Gas pipe should be protected from damage.
• If a centralized gas supply is provided in the bath, the removal of combustible products into the atmosphere should be installed.

Only subject to the above-mentioned conditions, the gas furnace for the bath can be installed.

Requirements for the furnace

Such requirements apply to all types of furnaces, but they should not be neglected:

• The gas stove for the bath must be fireproof, Compact, convenient to use.
• Have sufficient power to heat the room, ensure the desired number of steam.
• Models equipped with a heat exchanger must heat the desired amount of water.
• The heat should be enough for drying room after the end of the procedures.

Types of gas stoves for bath

The gas stove for the bath is a device for heating the room. Gas furnaces with a heat exchanger are used for autonomous heating and water heating. They are not capable of maintaining high temperature and humidity.

Gas furnaces for baths are divided into several groups according to certain signs:

• on the burner used;
• by manufacturing material;
• used by the type of fuel;
• according to the water heating method.

Gas stoves for baths can be made of stone or be with a metal case. Each view has its own advantages and disadvantages.

Used burners in gas furnaces

In gas furnaces, burners of two types are used: atmospheric and upgraded.

• Atmospheric burners have the highest possible device. No electricity is required for them and serious automation does not apply. According to special pipes or through the coil door, air is supplied. The efficiency of the operation of the furnace of this type is directly dependent on the quality of air supply to the chamber. If the oxygen inflow occurs in small quantities, the gas burning is not fully carried out, and this significantly affects the efficiency of such equipment.
• Superior burners have a more complex device, they are energy-dependent devices. Here, the injection of air into the chamber is due to the operation of the fan. This design is very effective in work. They use universal turbocharge burners, which allows them to be used in combination mode (atmospheric burners are not suitable for such a job).

The burner of this type is not suitable for a brick oven. This system requires complete tightness of the chimney and ovens for fan operation. The brickwork "breathes" by itself, due to the material used.

When the fan is running, a certain pressure is created, the exhaust carbon monoxide can penetrate the room.

Heating of water in gas furnaces

Gas furnaces can maintain not only the desired temperature in the bath, but also produce water heating. For these purposes, the furnace is equipped with a heat exchanger, the energy of the combustion products of the furnace are used to heat the water, which are removed through the chimney system, as well as heat of heated stones.

Water tank can be placed above or under a stone. In such a design, the chimney is carried out through the water itself. To solve the compactness of the unit, it will be an ideal model (it takes place no more than the unit without water heater).

Heating can be done and at the expense of the case - then the tank hanging is performed on the back of the furnace either side.

Automation for Gas Kamenka

This is a serious question that defines the safety and quality of the design.

You should choose according to these principles as:

• temperature maintenance level;
• degree of protection;
• when creating an emergency, the gas supply to the system must stop;
• when the system is deployed, an emergency shutdown must be made;
• must control gas supply pressure to the system, when leakage detection, the system must be disconnected itself;
• the presence of built-in pneumatics to disconnect the fuel supply.

Brick gas furnaces

Furnaces of such a design are warm up long, but they are well kept warm. Therefore, it is necessary to warm up early.

The appearance is not much different from the most ordinary wood-burning oven. She will be perfectly looking in a traditional style bath. The cooker is used to access the heater, which is inside the design. It is heated from the streams of warm air, which rise due to the combustion of the gas.

Here, directly above the burner is the Kamenka, to which they are presented special requirements. Stones for heating are located in a trough made of metal, which has the entire perimeter of the side (this does not allow water to fill to the fire).

Metal gas furnaces

A gas furnace for the bath with their own metal hands is distinguished by a relatively small thickness of the hull walls and a small number of stones in Kamenka. Such a model is quickly warming up, but also cools too quickly. Models of this type are quite compact, they can be equipped with a bath of almost any square.

This design is cheap by cost. If there is a small set of tool, it can be made in the shortest possible time. Here we will describe the manufacture of a gas furnace, which runs from the gas cylinder. Many have a positive response about such a design that has a very simple device.

Principle of gas furnace

In a separate chamber, which is located in front of the burner, gas is mixed with oxygen. Air enters the furnace and provides normal burning. To ensure air supply and the possibility of cleaning the burner at the bottom of the furnace, the door is mounted. Gas supply is carried out through the tube.

If the oven uses balloon gas, it should be taken enough to this. Such a balloon should be placed outside the room of the bath. Some install cylinders in the ground, a few meters from the bath. It should be borne in mind that the propane mixture is more efficient for the furnace.

The necessary materials

Materials are required to prepare in advance.

This will not disappear while working:

• Many write that you can use any old gas cylinder to ensure the work of the furnace.

ATTENTION: Do not use old cylinders! Not only you are subject to danger, but such a balloon is not fought with gas. Only those that have passed verification are accepted for refueling. The old cylinder will not be accepted.

• Any brake disc, most importantly, without cracks, it will serve as the basis for the heater.
• Buy two gas pipes with a diameter of 50 mm (they will provide a gas supply and air supply to the camera) and one with a diameter of 100 mm (chimney will be made of it).
• Gas burner (better atmospheric type).
• Connection connections.

In no case do not take compounds made from the silumin. They are cheap, but when heated or a small impact immediately burst. You should buy made of copper or bronze.

Installation of the furnace

To begin with, we produce a cylinder with the help of a grinder and a cutting circle. The diameter of the cutting base must correspond to the radius of the brake disc, so that without problems it is possible to fix it. When fasteners, it is best to use welding, after which the metal should be cleaned with the help of the grinder and the enlightest circle.

• For air supply to the system, you prepare a pipe with a radius of 50 mm. We make in it about 10 holes with a diameter of about 5 mm.
• We do a hole slightly more pipe diameter at the bottom of the cylinder. We produce pipe mounting so that the whole end is 20 cm from the cylinder. Write the joint.

• Such a system is fastened with a pipe for supplying gas.
• To connect to the gas, install the gas mounted adapter. The joke is processed by a sealant.
• We produce the fastening of the chimney at the top of the pipe.
• Cut a hole for the door. The curtains are attached to the carved piece of metal and attached to the body.

When mounting the oven is extremely important to protect the wall from overheating and fire. For this, a canvas from the clay is mounted between the oven and wall. Such insulation is made in two layers. In complete, the reflective screen of stainless steel should be applied. Possible equipment furnace with heat exchanger of indirect heating.

Competently selected gas stoves for the bath and high-quality installation work will provide you with a comfortable and safe rest.