How to remove the back cover at the HP Pavilion DV6 laptop. Step-by-step instructions for disassembling and cleaning a laptop HP G62-B51SR
Your HP Pavilion DV6 laptop has become very hot and noise even at low loads? Most likely, it just has time to clean the cooling fan bursting the fan. So, how to disassemble the HP Pavilion DV6 laptop and return it to the previous working condition?
HP Pavilion DV6 laptops are powerful, stylish, multimedia devices that have become quite popular in their segment. HP managed to create a quality product, but, unfortunately, having one disadvantage - a high level of heating and, as a result, noise. The laptop cooling system has two modes of operation - quiet and loud. With minimum loads, DV6 works silently, but it is worth loading the device as the cooling system is actively involved in the work, making some noise. Over time, the fan that serves air is clogged with dust, the effectiveness of its work is seriously reduced, and such indicators as noise and heating increase. In this case, the laptop should be disassembled and cleaned. You can pre-underload and compare it after cleaning.
How to disassemble a laptop HP Pavilion DV6 yourself?
Disassembly HP Pavilion DV6 does not pay difficult actions requiring special training. You can disassemble a laptop and at home, even if you have never previously disassembled computer equipment. Following the detailed instructions of actions from the next video, you can easily disassemble, clean and assemble.
Briefly an action algorithm can be described as follows:
- Remove the battery
- We unscrew the bottom cover (screws from the lid are not removed)
- Give hard disk, RAM, DVD-ROM
- Remove the keyboard, after unscrewing the desired screws
- Unscrew and remove the top cover
- Unscrew the display
- We disassemble the fan, remove all the dust from it
- In the reverse sequence, we collect everything back
Remarks: screws in a laptop of four kinds (first - hold the bottom cover and hold on it, that is, not removed; the second - keep the keyboard and are marked with a special icon; the third - hold the top cover; the fourth are very small on the fan itself), so not so that not Convert them to each other, when disassembling, you need to prepare boxes for each type in advance. Before removing the keyboard or something else, do not forget to disconnect the loops, and when assembling, you will definitely connect them to the place! The HP Pavilion DV6 fan is seriously clogged with dust for the first year of use, so it is highly recommended to clean it every six months.
The HP Pavilion G6 laptop was very grainbed even with a simple communication on Skype, with what, the fan accelerated to the maximum, and the exit air from the fan did not feel. The output of D-Sub was heated so much that it was even possible to burn it about it (about its metal part)
Photo of the laptop HP Pavilion G6:
Before disassembling, be sure to turn off the laptop from the network and take out the battery, moving the holder to the left side:
We unscrew two screws from the back cover:
Remove the back cover by attaching a slight effort, since in addition to the bolts it is still holding a latch. After removing the lid, you immediately unscrew four coils:
With something one of the cogs keeps the keyboard, on the top of the top it is in the very top of the left.
For the label, disconnect the wire of the hard drive from the motherboard:
We take out the hard drive (it does not hold anything else):
Disconnect the antenna wiring from the Wi-Fi module, unscrew one screw to the holding this module and take it out of the motherboard slot:
Unscrew all screws (12 pieces) from the laptop housing:
We turn over and open the HP Pavilion G6 laptop cover to remove the keyboard. In addition to the screw (which was unscrewed earlier), the keyboard holds a latch on the housing, which are pressed with a flat small scolding inside the case here in these places:
Also, the holders are both on the sides, they are in these places:
As soon as the keyboard is released, it is necessary to take it carefully in order to disconnect the keyboard loop from the motherboard:
It disconnects it very simple, you only need to turn the loop lock, which presses the loop to the connector on the motherboard, 90 degrees:
We remove the keyboard on the side and unscrew the two bolts that were under it:
Now we need to disconnect these two loops (go to the touchpad):
Everything is also very simple here, the locksters turn 90 degrees and the loops calmly come out of the motherboard connections:
In the left upper area, near the fan, it is also necessary to disconnect another loop:
It is disconnected in a similar way, like the previous ones, that is, the lock must be rotated 90 degrees:
After all, you can remove the decorative / protective lid of the laptop, which hides all the insides of the laptop. In addition to the bolts, it also keeps the same latches, start shooting it better from the right upper edge:
After removing the decorative / protective cover, we observe the following:
Here we will need to disconnect several loops and wires, start from the bottom left corner:
After disconnected above the selected loop and the wire - we remove the transparent yellow film, under which "hiding" another wire with a connector:
It is simply disconnecting from the motherboard connector:
Go to the upper left corner:
I pull the label and disconnect the monitor wire from the connector:
Upper right angle, disconnect the USB loop with a swivel lock:
And below this loop is hiding another bunch of wires (nutrition), which also needs to be disconnected from the motherboard:
Here be careful because it does not immediately succumb, but in the end it should turn out to be disconnected:
Returning to the left lower corner and unscrew the screw that keeps the motherboard:
Now the motherboard does not hold anything and can be removed by pulling slightly to the right and raising up. Laptop case without motherboard:
The housing of the laptop is removed to the side, and in front of them we have a motherboard:
We unscrew the screws (7 pieces) pressing the cooling system to the processor and the processor of the video card, as well as immediately disconnect the wires of the fan from the motherboard:
Cogs are unscrewed:
Carefully remove the cooler (radiator with thermal tube, venues and fan):
Turning over the motherboard, we notice that one of the attachments fell off, it will be necessary to fix it when assembling, otherwise it will not work out by the screws to press part of the radiator to the processor of the video card:
Go to the fan, we need to remove it and first unscrew two coils:
HP Pavilion DV6 laptop disassembly will be made to eliminate overheating. At first, I highly recommend you to familiarize yourself with the article where I tell how to determine whether overheating has a place and whether to disassemble the laptop at all.
Suppose we have diagnosed "overheating" and need to take the necessary measures. First of all, clarify whether the warranty period ended, because After parsing the laptop, the warranty will be canceled.
A warning: All responsibility for the result lies with you. Before doing something, please read the article to the end, to adequately appreciate your capabilities.
HP Pavilion DV6 laptop disassembly will be held in two stages - disassembly, then cleaning.
Disassembly of the HP Pavilion DV6 laptop
Remove the battery. To do this, shift the latch as shown in the picture.
We unscrew the 4 screws and remove the lid.
Under the cover, we disconnect the hard disk cable (pull over the Ushko up) and get the hard drive.
We unscrew the screw that holds the DVD drive. Give the drive.
We disconnect two wires from the WiFi module (remember their location).
Near the WiFi module is a train, which also needs to be disconnected.
We unscrew the remaining 16 screws.
Remove the keyboard. You need to pick up the keyboard from above and raise. It is necessary to do it carefully, so that it would not damage the loop that holds the keyboard.
If the keyboard is not bred, you can push it through the hole at the bottom of the laptop.
Under the keyboard, disconnect the loop. To do this, you need to open an eye.
Three loops will be available, which should also be disconnected.
Now you can remove the top panel. Under it we get access to the motherboard, where you need to disconnect four loops.
Under the train from the matrix hides the screw to be unscrewed. We unscrew the screw and remove the black plastic piece.
Remove the fee. Disconnect the power cable.
Everything. We are in our hands. You can go to the next step.
Cleaning a laptop from dust
We unscrew the four screws that fasten the radiator to the board. Turn off the fan power.
Remove the cooling system. Then open the fan housing. To do this, unscrew four small screws.
We remove dust everywhere where we see. The old thermal chaser also should be removed from the radiator and the chips. After that, you need to apply a new thermal path with a thin layer and replace the thermal layer.
In no case do not use the thermal paste instead of thermal blocks. I also do not advise you to use the cheap Chinese thermal staple. It has bad heat resistance.
We collect in reverse order. Good luck!
If you first start disassembling a laptop, we recommend paying attention to the article ". This article has recommendations that will help to avoid typical errors in the disassembly process.
HP Pavilion DV6 3000 Series Series is based on the same case as well as HP Pavilion DV6 3000 SERIES: DV6-3000ER, DV6-3010ER, DV6-3015SR, DV6-3015SW, DV6-3016ER, DV6-3020ER, DV6-3020SY, DV6- 3022SR, DV6-3025ER, DV6-3025SY, DV6-3026ER, DV6-3030ER, DV6-3030SY, DV6-3035ER, DV6-3040ER, DV6-3040ES, DV6-3040W, DV6-3040SL, DV6-3040SP, DV6-3050ER, DV6-3055SR, DV6-3056ER, DV6-3057ER, DV6-3060ER, DV6-3064ER, DV6-3065ER, DV6-3070ER, DV6-3072ER, DV6-3075ER, DV6-3080ER, DV6-3082SR, DV6-3085ER, DV6- 3090er, DV6-3101ER, DV6-3102ER, DV6-3103ER, DV6-3104ER, DV6-3105ER, DV6-3106ER, DV6-3107ER, DV6-3108ER, DV6-3109ER, DV6-3110ER, DV6-3111ER, DV6-3112SA, DV6-3120US, DV6-3121ER, DV6-31222ER, DV6-3123ER, DV6-3124ER, DV6-3125ER, DV6-3126ER, DV6-3140EC, DV6-3140US, DV6-3150SR, DV6-3151ER, DV6-3152ER, DV6- 3153ER, DV6-3153NR, DV6-3154ER, DV6-3155SR, DV6-3156ER, DV6-3170SR, DV6-3172SR, DV6-3173ER, DV6-3174ER, DV6-3229ER, DV6-3298ER, DV6-3299ER, DV6-3300ER, DV6-3301ER, DV6-3302ER, DV6-3304ER, DV6-3305ER, DV6-3327 SR, DV6-3328SR, DV6-3332ER, DV6-3334ER, DV6-3335ER - These models have the same disassembly process.
Writing a laptop from dust HP Pavilion DV6 3000 Series
If the laptop overheats during operation and turns off sharply - it is soon due to overheating of the cooling system. The reason for this is the accumulation of dust on the radiator. If you do not clean the cooling system on time, it will drive the motherboard breakdown in the laptop. This problem can be resolved independently, repeating all the steps shown in the video below. Information provided in our video instructions allows you to clean the laptop from dust yourself at home. The necessary tools for repair can be purchased at the end of the page.
Replacement keyboard in the HP Pavilion DV6 3000 Series laptop
The keyboard repair in most cases is caused by spilled tea or coffee to the surface, and as practice shows there are two outcome options:
- Remove the keyboard keys and clean their mechanisms using distilled water or alcohol using a brush.
- Replacing a new keyboard (if the cleaning of the buttons did not help), then the liquid hit the lower layers with the films where the tracks are located.
Replacement Matrix Laptop P Pavilion DV6 3000 Series
The matrix is \u200b\u200bthe most fragile detail of the laptop, often when the matrix falls, it is impossible to restore it, only replacement for a new one. There are different types of matrices, they differ in diagonal and the number of "PIN" of the connector (30PIN / 40PIN). To correctly pick up the desired matrix for your laptop, you need to know the number (Part Number) of your broken screen along which the same new or other compatible model of the matrix is \u200b\u200bselected. On the video below, you can see the replacement of the laptop screen and also learn part number compatible model.
Reverse Assembly P PAVILION DV6 3000 SERIES
After the disassembly and repair is completed, this video will help you to assemble a laptop to its original state.
Why is HP Pavilion G6-2323SR heavily heats up and noise? All simple! The problem of any laptop, and however, any portable technology is the small channels of heat removal, which over time are polluted and clogged with dust. Due to the limited space and lack of heat output (dusty growth) from a laptop, the temperature inside the technique rises. As a result, he begins to warm very much. So that there is no overheating of the system, capable of damageing the components of the laptop, the cooling system fan begins to work hard to remove heat. Because of this, the noise of work increases.
To eliminate such defects, a mechanical cleaning of the cooling system is required. And the usual prophesion of the radiator holes on the laptop housing in the absolute majority of cases of the positive effect does not bring. Therefore, further on a specific example, we consider how the HP Pavilion G6-2323SR is disassembered and the subsequent cleaning from dust. At the same time, I will perform the replacement of the thermal paste to improve the thermal conductivity of the "bottleneck" processor-radiator.
How to disassembleHP.Pavilion.G6-2323.sr.
The first step is to de-energize. Turn off the power supply and remove the battery.
Next, remove the keyboard. To do this, it is necessary to pick it up with a small flat screwdriver. Next, we drive a screwdriver along the keyboard, remove the latches.
When all the latches are unfounded, turn the keyboard and turn off its train from the motherboard.
Remove the keyboard to the side. Unscrew all the screws (all of them 5), which were hidden under the keyboard. And also turn off the entire loops that see.
Close the HP Pavilion G6-2323SR screen and turn the laptop. In the center of the case there is a screw. Unscut it first.
Next, from the side where the accamulatory battery was. There is an inscription "Release Door" and the arrow indicating the direction. We shift the lid in this direction. If it does not work with your hands, you can pry a little flat screwdriver.
Under it there is a hard disk, RAM and several loops. For convenience, everything should be turned off and removed.
Do not forget about the Wi-Fi module. Turn off the wires from it (white and black) and unscrew the locking screw.
Under the hard disk there is another screw that you should unscrew.
And then unscrew all the screws on the laptop housing in a circle. After that, remove the drive for reading hard drives.
Now you need to disconnect the case. To do this, from any convenient sides, we apply a flat screwdriver or a plastic card and disgust the first latch.
If all the screws are unscrewed and the loop is disabled, then by moving around all the latches in a circle, the case will easily figure out.
Before us is the motherboard. But there is no access to the cooling system, as it is located below. To remove the board, you need to turn off all the plumes and unscrew one screw.
After that, the board is very simply removed from the seats. Inverting it, a cooling system is visible in the form of a radiator and a fan.
In fact, on this disassembly of HP Pavilion G6-2323SR completed. But we need to clean the cooling system. So remove the radiator with the fan.
Next, disconnect the fan from the radiator, unscrewing the locking screws.
After that, there must be something like this (maybe worse, it can better) ...
Remove the dirt and tassel sweeping dust.
If the thermal paste is required on a laptop, then we clean the chips of the central processor and the video processor ..
And playgrounds on the radiator ...
On the chips purified from the old thermal panel, we apply a layer of fresh.
And we collect everything in reverse order. On this cleaning and replacement of thermal paste on HP Pavilion G6-2323SR completed. At each step, do not forget to check all the contacts and the loops so as not to have to repeat the laptop again.