Password from Waifa Dir 300Nrub7. Hardware reset to factory settings

The D-Link router DIR 300 models is one of the most popular in Russia and Ukraine. However, do not everyone know how to configure the password on Wi-Fi on the router DIR 300. How to put a passwordon this device, we will explain in this article.

Initially, it is better to check whether the router is configured at all and whether it distributes the Internet. If everything is in order, you can start setting the password.

DIR 300 Router: How to put a password?

To do this, we immediately run the browser that you usually use and go to the address bar. We prescribe in it 192.168.0.1 - this is the address of your router. If after writing this combination of numbers and pressing ENTER transition to the login and password page did not happen, try to register 192.168.1.1.

To put a password on the DIR 300, you need to select a picture with the "Configure Manual" inscription, in the window that opens, select the WiFi tab, and then "Security Settings". Here fill in the settings:

  1. Network authentication - WPA2-PSK.
  2. PSK encryption key is our password. You must come up with a rather complicated password to protect the network from hacking. If possible, it includes Latin letters, numbers, the letters of the upper and lower register.
  3. WPA encryption settings - leave as they are installed by default.

The next time you connect your computer or laptop to the Internet, you must delete an old access point in the network management center (control panel) and create a new one, already with a password.

Setting the password on the DIR 300 router more new versions is almost no different from the installation on old versions, so there will be no difficulties.

Good day to everyone!

Since you have fallen on this page, most likely you have some problems with the configuration of the home router from the company D-Link. For those who did not know or forgot the factory password to the "admin" router D-Link, the DIR-300 model, we inform:

the Password field is left blank. No, there is no password default!

Such is the interesting feature of this model. For curious, we will conduct a brief debt rate of DIR-300 to factory settings and receiving administrative access for further configuration.

How to set up routerD-Link, learn in the next video instruction:

Hardware reset to factory settings

So, you have something went wrong in the work of the router. And otherwise, why do you need access to the administration panel? In this case, one of the ways to restore the performance after any failure or previous "crucial" router adjustment is to perform a hardware reset, and then all set up correctly and so how it should be. To do this, take the recovery tool and clamp it (for 10-15 seconds) the RESET button, usually recessed into the housing near the appropriate inscription.

Recovery Tool - a comic name, common in narrow circles of specialists, and means a thin pin, stud, and just any piece of rigid wire, which allows you to press the buttons in hard-to-reach places of the case.

Access to the administrative panel

After 15 seconds let go and wait for the original loading of the device. Next, we connect any of the four LAN ports with a computer, and the cable from the provider is connected to the WAN port. On the computer, run any browser that is convenient for you and type the address 192.168.0.1 at the command prompt.


If everything is performed correctly, the browser window will load the router's administrative panel page. In the "Login" field, enter the admin, the Password field is left empty and press ENTER. As mentioned earlier, there is no default password in the DIR-300. Therefore, you must successfully log in if the hardware reset is correctly performed before that.

At the bottom of the router housing, a sticker withthe IP address of the administrative panel and the "Login / Password" pair for access.

After a successful entry into the administrative panel, the first thing you need to install your password on the D-Link DIR-300 router, because the standard (read - "empty") password on D-Link routers you know not only you.


Next configures the connection to the provider and the Wi-Fi password is installed. Usually these procedures are enough to safely use the DIR-300 and its updated version of NRU. Everything else applies to the "fine" setting of this equipment.

Finally, the personal opinion of the author of the article. In the settings, you must definitely disable Wi-Fi authorization procedure using the WPS code. The authentication mechanism is though convenient, but very "holey". Those who care about the safety of the home network, do not use it better.

In this instruction, consider in detail all the steps that will help you set up a Wi-Fi router D-Link DIR-300 NRU hardware revision B7 for "Home Internet Beeline". The following steps will be studied in the manual:

  • Preparing for configuration, connection of the router, information about firmware update, whether it is necessary to produce it.
  • The most common errors that are performed when setting up the router.
  • Configuring L2TP Beeline connecting to DIR-300 Rev.b7.
  • Setting up a wireless network, how to put a wi-fi password.
  • Configuring TV-TV - digital television IPTV.

The process of configuring the router is not something that could not be able to cope with absolutely any user if there is a competent and detailed written instructions. That is, I try to write. Go!

Update: If the firmware is installed on your router 2.5.11 or 2.15.19 (in general, 2.5.x), and the settings interface is similar to the screenshot below, use this instruction :.

Connecting a router to a computer, preparation for setting, how to flash router and whether it is worth doing

Connect the Wi-Fi D-Link DIR-300 B7 router is not difficult: just connect the Beeline cable to the Internet port on the back of the router, and one of the LAN ports connect the cable with a similar connector on a computer or a laptop from which the setting will be configured. Plus Turn on the router power. By the way, if you do not plan to flash a router (on this below), then, in principle, all the actions for configuring the device can be performed by Wi-Fi - from the tablet or even the phone.

Now about the firmware D-Link DIR-300 B7: If for some other models of D-link routers, I recommend updating the firmware, then the router of this modification is usually normal and without this process. Thus, you can perform all the router settings and contact the firmware update method only if any problems appear, such as:

  • Frequent spontaneous connection breaks, "cure" which helps only reboot the router.
  • Low Internet speed via Wi-Fi, Router "cuts" speed.
  • Other problems of obscure origin.

The penultimate: if you have already tried to configure your DIR-300 B7, but you did not work before continuing to reset the router to the factory settings. To do this, with the router power on, press and hold the reset button from the back of it 10-15 seconds, then release it. Another seconds will take a reboot of the router with factory settings.

And last: Before setting, tear the Beeline connection on the computer you use to access the Internet. And do not connect in the future - after setting up the router itself will set this connection and after that it is possible to distribute it to the local and wireless Wi-Fi network to all devices. Otherwise, if you do not disable this connection, you will have a question about why there is an Internet computer, and the Wi-Fi is connected, but without access to the Internet. And I am very tired of answering this question.

Configuring L2TP Beeline Connection on DIR-300NRU B7

The main stage when setting up any wireless router (Wi-Fi router) - to properly configure the connection settings in it. What we will do - in our case it is the DIR-300 B7 and used in the Beeline type L2TP connection. So, proceed.

Run your favorite browser and in its address bar, enter 192.168.0.1. The next thing you see will be querying the username and password to enter the D-Link DIR-300 NRU B7 router settings. Standard values \u200b\u200b- Admin and Admin, there and there.

After entering the correct data, you will find yourself on the main page of the router settings. However, we will not delay on it: at the bottom of the "admin", select the "Advanced Settings" link.

On the next page, in the Network item, click on the "WAN" link, then click the Add button, not paying attention to the connection that is already in the list. Now you are on the Internet connection settings page, it is necessary to enter the correct parameters for the Beeline Provider.

Fields should be filled as follows (in those that are not mentioned here, the values \u200b\u200bshould not be changed or not necessary):

  • Connection type - L2TP + dynamic IP
  • Username - Your login to access the Internet Beeline
  • Password - Your password for internet access
  • VPN server address - TP.internet.beeline.ru.

In general, it's all you need to change. After that, click "Save". After that, you will find yourself on the page on which the newly created connection will be displayed in the "broken" state. Also on top to the right will flash the light bulb and the number is displayed one: if you click on it (and this should be done) you will be prompted to save the device configuration again - click "Save".

Now just update the current page with the list of connections and, if you have not made errors, and the Internet Beeline on the computer itself is disabled, you will see that the connection status has changed from "broken" to "connected", which we needed.

L2TP Beeline connection is connected and running

Now the computer from which the setting is made has full Internet access on the local network, and if you connect via Wi-Fi from another device, then the Internet will also be released. However, you should not hurry to check. First, it is better to finally configure the router, namely the parameters of the wireless Wi-Fi network.

Wi-Fi setting on DIR-300 B7

In order to configure Wi-Fi to the DIR-300 B7, return to the advanced settings page and in the Wi-Fi item, select "Basic Settings".

On this page, you can configure the following parameters:

  • SSID. (Wi-Fi Access Name) - Enter the desired name, English characters. This name will allow you to distinguish your wireless network from neighboring. By default (and recommended), apparently everyone in the access point zone.
  • Country - Network Standard. By default, the Russian Federation is installed, but I recommend changing to the United States. Some devices do not see or do not connect to the point with the region of the Russian Federation. Everything is connected to the USA without exception.

The remaining parameters can be left unchanged. Save the settings made. Now in the Wi-Fi paragraph, click the Safety Settings link.

  • Network authentication - WPA2-PSK
  • PSK Encryption key - The desired password on your wireless Wi-Fi network needed to connect to it. Must consists at least 8 Latin characters and / or numbers.

Save all the settings made. Router is ready to use.

Setting IPTV Beeline (digital TV via router)

In order to configure Beeline Television on the DIR-300NRU B7 simply go to the main page of the router settings (Quick Setup) and click on the "IP Television" item. In the next step, you will be prompted to choose the port on the router to which you will connect the television console Beeline. Select the appropriate and save the settings. Ready.

In case you have refused to work - write comments. If everything has earned - also write (I will be pleased) and share the instructions on social networks - it will allow others easier to find it.

Setting up the router DIR-300 / NRU / B7


Connect Wi-Fi Router D-Link DIR-300 NRU REV. B7.

The newly acquired and unpacked router is connected as follows: the provider cable (in our case is medialan) connect to the yellow port on the back of the router signed by the Internet. The attached blue cable in one end sticking into any of the four remaining router sockets, another in the network card connector of your computer. We connect the power to the router and wait when it boots, and the computer will determine the parameters of the new network connection (do not be surprised that it is "limited" and necessary).

Note: During the router configuration, do not use the medialan media to the Internet on the computer. It must be disabled. Subsequently, after setting up the router, it will also no longer need - the connection will install the router itself.

It will not be superfluous to make sure that in the local network connection parameters for the IPv4 protocol settings are set: to receive IP address and DNS servers addresses automatically. To do this, in Windows 7, click the connection icon below to the right, select "Network and Common Access Control Center", then change the adapter parameters, with the right click on the "connection on a local network - Properties, and make sure that they are not written there any either static addresses. In Windows XP, the same properties can be viewed in the Control Panel - Network Connections. It seems that the main reasons for which something may not work, I took into account. We go further.

Connection setting in DIR-300 Rev. B7.

The first step to configure PPOE (using the medialan) on the D-Link DIR-300 is the launch of your favorite Internet browser (Internet Explorer, Google Chrome, Mozilla Firefox, Safari on Mac OS X, etc.) and the transition to the address 192.168.0.1 (Enter this address to the browser address bar and press ENTER). As a result, we must see the request for login and password to enter the DIR-300 B7 router admin.

Login and password for DIR-300 Rev. B7. Standard login for login - admin, password is the same. If for some reason they are not suitable, then maybe you or someone else changed them. In this case, you can reset the router to the factory settings. To do this, press and hold something thin (I use toothpick) for 5 seconds the RESET button on the reverse side of the router. And then repeat the first step.
After entering the login and password, we will fall in the D-Link DIR-300 Rev router settings menu. B7.


D-Link DIR-300 REV. B7 - Administration Panel
Here we need to choose "Advanced Settings", after which you will see the page on which the model of your Wi-Fi router will be displayed, the firmware version and other information.
In the top menu, select "Network" and fall on the WAN connections list.

In the image above this list there is one WAN connection. We click on the WAN connection, you must have the following settings: Connection Type (Dynamic IP), also need to put a tick - get the address of the DNS server automatically. The MAC address will need to be cloned, because There is a binding for MAC addresses. Click Save.

After you have saved the WAN settings, press the Add button, in the lower right corner and get to the main WAN settings. This time we select PPPoE in the "Connection Type" field. Then, instead of a standard connection name, you can enter any other (for example, I have a medialan), in the "Username" field, we enter your username from the Internet medialan, in the password field and password confirmation - respectively. We put the Keep Alive tick and click "Save". On the next page, where the newly created connection will be displayed, we will again be offered to save the configuration. We save.

Now, if all operations above were completed correctly, if you are not mistaken when entering the connection parameters, then when you go to the "WAN" tab, you should see the next joyful picture:

Pay attention to the mark in the default gateway, the default should be the PPPOE compound you created. If all three connections are active, this suggests that the most basic to configure the D-Link DIR-300 NRU Rev. B7 We have successfully completed, and can move to the next step.

Setting up Wi-Fi connection DIR-300 NRU B7

In general, the Wi-Fi wireless connection can be used immediately after turning on the router to the network, but in most cases it can be useful to configure some of its parameters, in particular, set the password to the Wi-Fi access point so that the neighbors do not use your Internet. Even if you do not feel sorry, it can affect the speed of the network, and the "brakes" when working on the Internet, most likely you will not be pleasant. We go to the Wi-Fi tab, the basic settings. Here you can set the name of the access point (SSID), it can be anyone, it is desirable to use the Latin. After this is done, click Edit.

Now go to the "Security Settings" tab. Here you should select the type of network authentication (preferably WPA2-PSK, as in the picture) and set the password to your WiFi access point - letters and numbers, not less than 8 characters. Click "Change". Ready. Now you can connect to the Wi-Fi access point from any device equipped with the appropriate communication module - whether it is a laptop, smartphone, tablet or Smart TV.

UPD: If not working, try changing the LAN address of the router at 192.168.1.1 to the settings - LAN.


What you need to work tv from medialan In order to earn IPTV from the medialan via router, go to the first page of the DIR-300 NRU Rev settings page. B7 (For this, you can click fast setting in the lower right corner) and select "IPTV Setup Wizard". It remains only to select the port to which you connect the IPTV console. We click to change.

That's probably all, do not forget to save the router settings!