ASUS RT N10 C1 firmware. Installing the firmware from Oleg on the ASUS router. Installing a new firmware
1. Fixed Loading Issue in Repeater Mode
2. IMPROVED URL FILTER AND CONNECTION STABILITY
3. Upgraded LIBUPNP
4. Updated PPTP DRIVER
5. IMPROVED PPPD / PPPOE PERFORMANCE
About Router Firmware:
Before You Consider Downloading This Firmware, Go to the Sure Sure This The Currently Installed Version Isn't Either Releases Sure Entalled Version Isn't Either Release.
Due to the Large Variety of Router Models and Different Methods for Upgrading The Device, IT IS Highly Recommended That You Read And Above All, Understand The Installation Steps Before You Apply The New Firmware, Even If You Are A Power User.
In Theory, These Steps Shouldn't Be Much of a Hassle for Anyone, Because Manufacturers Try to Make Them As Easy As Possible, Even If thely don't Always Succeed. BasiCally, You Must Upload The New Firmware to the Router Through Its Administration Page and ALLOW IT to Upgrade.
If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.
If You're Looking for Certain Safety Measures, Remember That It Would Be Best If You Perform The Upload using An Ethernet Cable Rather Than A Wireless Connection, Which Can Be Interrupted Easily. Also, make sure you don't Power Off The Router or Use Its Buttons During The Installation, If You Wish Avoid Any MalFunctions.
If This Firmware Meets Your Current Needs, Get The Desired Version and Apply IT to Your Router Unit; If not, Check with Our WebSite Asissa As Possible So That You Don't Miss The Update That Will Improve Your Device.
IT IS Highly Recommended to Always use the MOST Recent Driver Version Available.
Try to Set a System Restore Point Before Installing a Device Driver. This Will Help IF You Installed An Incorrect or Mismatched Driver. PROBLEMS CAN ARISE WHEN YOUR HARDWARE DEVICE IS TOO OLD OR NOT SUPPORTED ANY LONGER.
Firmware 1.0.4.1 provides IPTV support in all modes (UDP-Multicast, UDP-to-HTTP Proxy, Stb-Port). IPTV is checked in the Ukrtelecom network. Allows you to use Ethernet WAN.
X.Wireless router and ADSL modem
Firmware 1.0.4.1 provides IPTV support in all modes (UDP-Multicast, UDP-to-HTTP Proxy, Stb-Port). IPTV is checked in the Ukrtelecom network. Also, the firmware supports work with 3G modems.
X.
Dual-band Wi-Fi Router
Firmware 3.0.0.4.314 (Annex A) with support for 3G modems and full support for IPTV Ukrtelecom.
Firmware 3.0.0.5.374 (Annex A) with support for Dual Wan, 3G modems and full support for IPTV Ukrtelecom.
Wireless standard n router with EZ UI interface
Firmware version 2.0.3.2 for RT-N10 B1 router, has increased throughput WAN-LAN.
X.
Wireless 802.11n 150 MBT / C with a powerful 5 DBI antenna for increasing coating zone wireless network.
Instructions for setting network printer or MFP
Firmware 7.1.1.1.32b
Wireless 802.11n 150 MBT / C with a powerful 5 DBI antenna to increase the wireless network coverage area. With the firmware version 3.0.0.3.135 supports 3G modems.
Firmware 3.0.0.4_374_5517 with support for 3G modems
Firmware 3.0.0.4.260 with new interface and 3G modems support
Firmware 3.0.0.4.321 with new interface and 3G modems support
Router, access point and repeater in one device. Two removable antennas with a gain of 5 DBI. Claused according to the 2T2R scheme, it provides a high data rate of 300 Mbps.
Firmware for ASUS RT-N12 D1 3.0.0.4.374.430
Firmware for ASUS RT-N12 D1 3.0.0.4_374_4230. Improved speed indicators on PPPOE connections.
Firmware for ASUS RT-N12 D1 3.0.0.4_374_4583
Wireless Router N Standard with Integrated Print Server
Firmware 2.0.2.5o for RT-N13U B1.
7.5.1.98 - Refrigerates the 3G modem of all Ukrainian 3G-communication operators and 802.1x Ethernet authentication protocol WAN-port router.
Wireless RT-N15U Router Wi-Fi 802.11n (300 Mbps), equipped with Gigabit Ethernet ports and intended for use at home or in a small office.
Firmware 3.0.0.4_374_4583.
Firmware 3.0.0.4.260 with support for 3G modems
The most recent firmware for RT-N15U.
Multifunctional Wireless N-Standard Router With File, Print and Media Server
Firmware Version 3.0.0.4.315 - New interface design, Support 3G / 4G (Freshtel, Giraffe), Aicloud
Firmware Version 3.0.0.4.321 - New interface design, Support 3G / 4G (Freshtel, Giraffe), Aicloud
Earlier, we considered how to configure different ASUS routers designed for 100 megabit networks. It was mentioned that the firmware can be replaced, but this action is associated with risk. If the user still decides to install on router Asus. alternative version Software, we recommend to start try firmware from Oleg. Also, here we will look at how the setting is taking.
What models of routers of ASUS are calculated by the firmware "from Oleg"? The answer is very simple. Enough to go to the oleg.wl500g.info website, scroll down the page down, click on the latest link "Firmwares" to see the list:
Official site of firmware "from Oleg"
Immediately download the file for the router model you are interested in (for example, WL500G), the main thing is not to confuse the revisions "500GP" with "500GP-V2". Then you unpack the archive to the desktop, and see one file with the * .trx extension.
Firmware for more "early" models (for example, 500G or 300) - are in the penultimate folder.
Note: If you have a router of another model (or even another revision) - the installation will not be possible.
Installation of firmware
Preparation of router
Before you configure Router Asus, you install a new firmware. To install it, you need to go to the Web interface. But the router may have already configured someone. Therefore, first - we will reset the RESET button to return the "factory" values, including the administrator password.
Button Reset.
The router must be turned on, after switching on, must pass at least 2 minutes, then you click Reset. It is necessary to hold the button for 10 seconds, and the settings will return to the correct values.
Compound connection
Patch cord must connect any LAN port of the router with a computer network interface. But, do not rush to turn on the router's BP: first check whether the network card is correctly configured. We recommend to set up like this:
"Properties" of the connection
You can watch the settings in the "state" of the connection -\u003e "Properties" -\u003e "Internet TCP / IP" -\u003e "Properties".
Last but you need to turn on the router BP and send a computer to reboot.
Installing a new firmware
We know that by default the IP address of the ASUS router is 192.168.1.1. Also, to enter the Web interface, you will need a password and login (this is the ADMIN pair).
You need to open any browser, in its address bar - to dial the IP address of the router, click "ENTER". Report login and password. And go to the Web interface (on offer automatic setting - Reply "No" or "Cancel").
The router produced by ASUS WAI can be endowed with one of the following interface options:
Interface: Option 1
Interface: Option 2
In the first case, we go to the "System Setup" tab -\u003e Firmware Upgrade. In the second - to the "Advanced Settings" tab -\u003e Administration, to the "Firmware Update tab.
Update: Interface 1
Update: Interface 2
In the first case, click "Review", we find the * .trx file, confirm your choice. Installation will start after clicking "Upload". In the second - also select the file. Installing the firmware - starts with the "Send" button.
Installation of firmware
After the start of the firmware process, you need to wait for completion. You can not close the browser, or turn off the router. If you still change the address of the IP of this router, after installing the firmware and reboot - it will have to be searched on the same address, and not at 192.168.1.1.
Note: When the power is disappeared on one of the devices (router, computer) - the installation of the firmware will not be executed. After that, you will have to restore the Router "Emergency Recovery".
Here it was discussed in detail how to flash ASUS router. Now, we will consider setting the router with a new firmware.
Setting the router with firmware "from Oleg"
Internet connection
We assume that all the necessary cable connections were executed, the router is turned on, and the computer is rebooted (and the network card received its IP address). Then, from any browser you can go to a new web interface. The entrance to the ASUS router is carried out with the same login / password that was before flashing.
From automatic setting, we will refuse:
Login to Web Interface
And we will see the first tab of the graphical interface:
Main tab
To configure the connection, you need the "IP Config" -\u003e "WAN-LAN" tab:
Connection Setup (DHCP Option)
If you configure the connection "under DHCP", it is not necessary to change anything on this tab. Only install the MAC address value you need (for example, as indicated on the bottom side of the router housing, or other). Now - go down the page, click "FINISH":
Saving connection settings
It will only be possible to agree with the reboot:
After that, the settings will be saved, the router will restart, and the connection will appear automatically. Then, you can check the availability of connections (by clicking on the "Status & Log" tab -\u003e Status):
Device status
We see that the connection is in this momentconnected ("Connected"). And install and configure the connection WiFi routerand asus as a VPN client - you will help the drawing below. Successful setting!
Connection Setup (PPTP option)
Connection setting (PPTP option), continued
Explanation: "User Name" - the subscriber name, "Password" - the password value (see Agreement), "NO Encryption" - to establish, "PPTP / L2TP (VPN) Server" - the name or VPN server address (see Agreement ).
About installing MAC addresses
It is noted that after flashing the router, the MAC address of its WAN port - always takes the value "00-90-4C-C0-00-00". In principle, if there are no other Asus routers nearby, equipped with the same firmware - Mac address can be left as it is. But still, it is recommended to establish it "explicitly" (as indicated from the bottom on the housing). In fact, you can ask other numbers as the Mac address that it will be useful if the provider checks mAC value (When there is a "binding" to the hardware address).
Wireless network and its setup
Enable the built-in access point and install the required parameters (network name, password, encryption algorithm), WiFi Asus router with Oleg firmware will allow you on the same tab. It is called "Wireless" -\u003e "Interface":
Basic Wi-Fi Settings
After you set the Network Name (SSID), the encryption mode and password (as in the figure) will sufficiently press the "FINISH" button. Router will reboot, after which wi-Fi network - It will be functioning. You can search for this network from any gadget - it has already appeared!
We did not consider how to make the "Channel" setting. This is the channel number (from the 1st to 12th), it is, in this case, the router will automatically select. And in the "Wireless Mode" string, the most "fast" mode is "AUTO" (it is also called "Mixed"). Note that here - not provided for the "N" mode.
There is another tab containing Wi-Fi settings. Here you can hide the network name. Also, the user can reduce the power of the radio transmitter (it is necessary, or not - it depends on how to install a WiFi Asus router in the apartment). Sometimes on reduced power, the network works better, due to the smaller influence of the reflected waves. To install these settings, go to the Advanced tab:
To "hide" the name, you need to install the "Yes" point in the Hide SSID line. Remember that the settings come into force only after pressing "Finish". Successful Routing!
Additionally
IPTV.
How to connect a WiFi router asus to a computer to watch digital TV? With firmware "from Oleg", it will be enough to turn on IPTV traffic (Multicast packets - will go to the local wired network and to the Wi-Fi network). Open the "IP Config" tab in the Web interface -\u003e Route:
Enable Multicast.
Install the two top ticks to the "Yes" value, and apply the settings. After that, any MultiCast package is no longer blocked in wired (and in wireless) local network.
In addition, in additional Wi-Fi settings ("Wireless" -\u003e "Advanced"), Multicast-traffic - can be forced to limit:
Advanced Wi-Fi Settings
Instead of "auto", you need to select a value where viewing TV via Wi-Fi will not interfere with other users (IPTV - should not occupy all Wi-Fi-Traffic). Pick up the value, gradually reducing it (here is available: 36 Mbps, 18 Mbps, etc.).
Advantages of alternative firmware
By installing the firmware "from Oleg", you will notice the following. Saving values \u200b\u200bin the device's memory - now occupies exactly 20 seconds. All options work as they should work, moreover, without interfering with each other. ASUS router does not work after flashing for only one reason: if the installation process is not fully fulfilled. Selection, install or not - leave a user responsibility.