Best zte wifi setting. How to set up a modem ZTE ZXHN H108N. Preparing to set up equipment

4G / WiFi router ZTE MF90 is quite extraordinary for 2015-2016 (it was then that the modem first appeared on the "mass" market), but at the same time, a high-quality device that meets the basic requirements for the functionality and mobility of the router.

It should be noted right away that the device is locked to work with the Beeline operator, and is sold mainly through the sales offices of this provider.

Router zte mf90 specifications: overview and specifications

For a fairly adequate price (in the region of three thousand rubles), Chinese developers have provided a high-quality mobile router with competitive characteristics.

1. Baud rate:

  • - with "LTE FDD" up to 100 Mbit / s - during reception, and up to 50 Mbit / s - during transmission;
  • - with "DC-HSPA +" up to 42 Mbit / s - reception, and up to 5.76 Mbit / s - transmission;
  • - with "EDGE / GPRS" up to 236 Kbps.

2. Support for micro SD memory cards up to 32 GB.

3. Li-ion 2300 mAh battery.

These characteristics fully provide comfortable surfing in the network: the battery allows you to freely use all the benefits of the Internet for 6-8 hours.

Router zte mf90: indicators and connectors

Due to its mobility, the router had to "sacrifice" the indicator part.

There are only three indicators on the front of the device:

  • - "Battery charge". When the indicator "burns" or "blinks" red, it is necessary to charge the battery. If the light “blinks” green - the battery is charging (the charge level is not lower than average or the battery is fully charged).
  • - "Network signal strength". The indicator is constantly "on" red - there is no signal, or "USIM" is not installed. "On" green - registration in the 2G / 3G network, "blinking" green - the router is connected to the network and data transfer is in progress, if the indicator "is on" blue - this means that the device is connected to the 4G network.
  • - "WiFi network". If the indicator "blinks" blue - the wireless network is on, if "on" - then "WPS" is on.

Below the indicator panel there are “Power” and “WPS” buttons, which are also designed to enable or disable the wireless network (with a single press), but if you hold the button for 5 seconds, the “WPS” mode will turn on.

On the side there are two connectors for connecting 2 additional antennas and a mini-USB connector for synchronizing with a computer or connecting a charger.

There are two slots inside the case under the rechargeable batteries: one for "USIM", the other for "microSD". And on the opposite side of the router, relative to the side buttons, there is a recess with the "Reset" button (ie reset to factory settings).

How to connect the zte mf90 modem by yourself?

The procedure for connecting a zte mf90 router is as follows:

Open the cover and insert it into the corresponding USIM slot of the Beeline operator.

  • - Pay attention to the sticker inside the case, where the "SSID" of the wireless network is indicated (indicated in the format MF90_XXXXXX, where x is a unique number assigned to each device) and the password. Remember them - in the future, this data will be useful to you.
  • - Install the battery and close the cover.
  • - Using the “Power” button, turn on the device (the corresponding indicators will light up) and connect the “USB cable” between the router and the computer.

  • - Search for available wireless networks (based on the above “SSID” name) and connect to the network by entering the password.
  • - Next, in the address bar of your browser, enter 129.168.0.1 or m.home (the default password is “admin”).

To change the password for entering the settings of the zte mf90 router, use the "Management" section. Here you can also configure the power saving mode, pin - code "USIM" and settings for sending "SMS messages".

How to set up an internet connection on a zte mf90 router?

Internet access is configured through the router interface.

The first step is to carry out the "Activation of the starting balance":

Open the "Service Management" section;

In the drop-down menu, select "Activate starting balance";

Click the "Activate" button.

If payment will be made using Beeline payment cards, in the Service Management section, select “Payment Card Activation” and enter the digital code of the card (without using spaces and hyphens).

You can also use the service "Request funds from another subscriber": in the same section, select "Ask for money from another subscriber", enter his phone number without the eight and click "Send". It remains to wait for the payment. But do not abuse this service, since there is a restriction - you can send a request no more than 5 times a day.

To complete the settings, you just need to click on the "Connect" button and select one of the connection modes:

  • - if you select "Automatic", then when you turn on the device will independently conduct an Internet connection;
  • - if you set "Manual", then to get access to the Internet, every time you turn on the device, you will need to visit the web interface.

How to set up wifi on a zte mf90 router?

To configure a wireless network, go to the "WiFi" section and do the following:

  • - enter the name of the network in the line "Network name (SSID)";
  • - check the box next to “Enable” in the line “Broadcast network name (SSID)”;
  • - “Network encryption type” leave “WPA-PSK” - “WPA2-PSK”;
  • - in the "Password" line, enter the security key to connect to the created network;
  • - in the “Maximum connections” line, set the maximum number of devices that will use this network (but no more than 10).

The Firewall section is used to configure port filtering and forwarding, and to enable or disable UpnP / DMZ.

The "Router" section allows you to change the "ip address" of the router, familiarize yourself with its "mac-address" and configure the "DHCP server".

In the section "WiFi Internet" you can configure and use "mf90" as a repeater.

In such a review, 4G / WiFi router ZTE "MF90" is an excellent mobile option for a relatively low price, which opens up vast opportunities for web surfing in transport, at work or in any other places where the use of regular routers is unacceptable.

Unlock router beeline zte mf90

Unlocking (unlocking) a ZTE MF90 router, and, in principle, all other routers tied to one provider, is not difficult, but requires attention (and an elementary understanding of where what is in the computer).

1. First, download and unzip the firmware to unlock the zte mf90. It will not be difficult to find it: for any request like "How to unlock an MF90 router", there will be many options where you can download this archive.

4. Now you need to put the router into diagnostic mode. Go to "http: //m.home/goform/goform_process? GoformId = MODE_SWITCH & switchCmd = FACTORY".
Please note that the diagnostic mode is a temporary parameter, so do not hesitate and go straight to the next step.

5. In the "Device Manager" new hardware will appear with the name "ZTE Mobile Broadband DiagnosticsPort" - open the "Ports" section and remember which port is assigned to COM4 or COM13.

6. Place the file with “.bin” resolution from the downloaded archive into the root of the “C:” drive.

8. Disconnect and restart the router.

In conclusion, you can check with any convenient utility for checking the binding whether your router is jailbroken or not.

The ZTE ZXA10 F660 router is a modern network equipment required to connect to the worldwide information network via a fiber-optic line (GPON technology). In terms of its functionality, it is both an ONT terminal and a Wi-Fi router, capable of distributing the Internet both via an Ethernet cable and wirelessly with an end device.

In addition to the standard features of the zxa10 f660 router, it also provides IP telephony and the ability to create a local Web server based on the router.

And this article provides step-by-step instructions for setting up a zte zxa10 f660 router from mgts, and also discusses some of the subtleties of connecting this device.

Router zte zxa10 f660: specifications and design features

The gpon ont zxhn f660 router is an economical mobile Wi-Fi transmitter with a main operating frequency of 2.4 GHz.

The functionality of the router provides Wi-Fi data transfer rates up to 300Mbps, while the device supports up to 4 SSIDs with 128 simultaneous connection of users to each network.

Also, the zte f660 router supports WPS mode, so the device can be used to expand the WiFi zone of another router.

On the back of the router there are:

  • - standard LAN connectors for connecting to zxa10 f660 devices via an Ethernet cable;
  • - two POTS connectors for implementing the IP telephony function (for connecting an RJ-11 telephone cable);
  • - two USB connectors for connecting external media (including for updating the firmware of the device and organizing a local Web server);
  • - POWER connector for connecting a power adapter;
  • - on / off buttons for WLAN and WPS functions;
  • - RESET button to reset the router settings to factory defaults;
  • - button to turn on / off the router.

The GPON connector for connecting a fiber-optic cable provided by the provider can be located both on the back and on the side of the zte f660 router.

Connecting the zte f660 modem

1. Connect the power adapter (supplied with the device) to a 220V electrical outlet, and its plug into the socket on the rear panel intended for it.

2. Connect the green plug to the optical cable port and the other end to a power outlet.

3. Insert the plug of the patchcord (Ethernet cable) into one of the four LAN sockets, and its other end into the network card connector of the computer, from which the MGTS gpon zte zxa10 f660 router settings will be entered.

When the router is connected to a PC, the indicator corresponding to the active LAN connector should light up on the front panel of the device. If this does not happen, it is recommended on this computer.

How to set up zxa10 f660 router?

Connection, testing and configuration of optical communication, as a rule, are carried out by specialists of the company-provider of communication services.

If you are installing the zte f660 optical modem by yourself, then call the service provider of the provider, ask to set up the equipment and follow the instructions of the specialist.

Zte zxa10 f660 router: WiFi setup

1. Launch any Internet browser installed on your computer and enter http://192.168.1.1 in the address bar.

In the field that appears, enter the login: admin, password: admin and enter the configuration interface of your device.

2. A menu with tabs will appear in the window that opens: “Status”, “Network”, “Security”, “Application”, “Administration”.

3. Go to the "network" tab, in the "WLAN" submenu and its subsection "Basic".

In the column "Wireless RF Mode" select the option "Enabled".

  • - Next, "Mode" should be set to "Mixed802.11b + g + n".
  • - "Country / Region" - "Russia".
  • - "Chanel" - "Auto".
  • - "Transmitting power" - "100%".

4. Click the "Submit" button, then go to the "Multi-SSID Settings" subsection.

In the “Choose SSID” box, select “SSID1”.

  • - Check the “Enable SSID” checkbox (Make sure the checkbox is unchecked for other SSIDs).
  • - Come up with a name for your network and write it in the "SSID Name" field.

5. Press the "Submit" button again and go to the "Security" subsection.


- Here in “Choose SSID” select the first option.

  • - Set "Authentication type" to WPA2-PSK.
  • - Create a password for the Wi-Fi network and enter it in the “WPA Passphrase” field.

The password must be unique and contain at least 8 Latin characters. It is not recommended to set standard and easy-to-guess passwords (for example, home address) in order to avoid unauthorized connections to your WiFi network.

How to change the password from the mgts zte f660 router?

To set a unique administrator password used to enter the settings of the MGTS gpon zte zxa10 f660 router, go to the Administration menu and the User Management submenu.

- Switch "User Right" to "Administrator".

Enter the old password in the “Old Password” field, and the new password in the “New Password” and “Confirm Password” fields.

It is also recommended to disable the WPS function before using the zte f660 router. To do this, press the corresponding button on the back of the device.

The router from the manufacturer ZTE is a model that can only work on FTTB lines. Configuring the ZTE ZXHN H118N router by Rostelecom can be done either using the wizard built into its program, or in manual mode. Supports IPTV and SIP telephony.

The entrance can be done only after connecting the cable of the Internet service provider to the WAN port (RJ-45) on the back panel of the ZTE ZXHN H118N Rostelecom router. One of the 4 ports of the LAN router (RJ-45) is connected by an Ethernet line to the connector of the network card of the computer (PC) or laptop used for configuration. You must first set the automatic mode of receiving addresses by the device on the Internet Protocol version 4 page.

According to the information on the sticker, it can be seen that the IP address of the device is 192.168.0.1 - and its authorization data is used by default: the username is admin, the password is admin. The network address is entered into the address bar of the web browser used on the PC, and information about the login and password is required to fill in the fields of the opened window.

The router program requires the obligatory connection of the provider's cable to the WAN connector, and the first login page will remind you of this in case of violation of the necessary condition. If the router detects an internet connection, then the page looks different. It displays suggestions for choosing a time zone and the need to change the factory password with the corresponding information fields.

After meeting the safety requirements, you must click on the "Continue" stencil and go to the next page. On it you need to select the proposed configuration method: "Start the wizard", "Configure the device manually".

How to make a menu complete

The Rostelecom router is configured after selecting manual settings. To enter the menu, you need to enter the data for the username - admin - and the created individual password. When you click on the "Login" tab, you go to the start page of the router interface with general information about the device. The item "Network" in the left part of it opens the possibility of choosing the type of WAN connection.

When configuring, the data provided by the provider when concluding an agreement with him is used: the type of Internet connection (PPPoE), the number of the enabled VLAN (fiber optic) and its priority, username and password. The connection you create must be Always On. The entered data is saved when you run the "Edit" command at the bottom of the page.

To use the watch TV function, you need to re-open the list of possible WAN connections and select IPTV in it. In the connection type string, use "Bridge" and then execute the "Create" command. To do this, go to the "Port binding" item in the WAN section of the main menu.

It is used for software assignment of LAN1-LAN4 connectors. For PPPoE, the default ports are LAN1-LAN3. Computers will connect to them. For IPTV, you need to assign LAN4. It will include a set-top box that will use it over an Ethernet cable line. After setting the checkboxes in the selected cells, press the "Save settings and confirm" button.

Configuring Wi-Fi on ZTE H118N Ethernet router

Router manufacturer ZTE provides its products with Wi-Fi configured. Information about the name of the network and the password to access it can be found on the label on the router. But the connection setting can be done manually. To do this, in the VLAN (Wireless Network) section of the menu, select the "Configure Wi-Fi networks" item.

On its page, you can change the factory values ​​to your own. After selecting the "Security" item, it becomes possible to change the authentication type and encryption algorithm. In conclusion, you must press the button to save ("Apply").

Popular settings

You can apply automatic configuration of the Rostelecom router after the proposed change of the factory password. If you then click on the "Start the wizard" stencil, then at the next step you need to select and indicate the region, branch and service of Rostelecom. After proceeding with the configuration, you must fill in the login and password fields provided by the provider when concluding the contract. If the branch office uses "Dynamic IP", this information is not required.

When connecting a set-top box, it must be assigned the LAN4 port. After continuing, the wizard will offer to change the authorization data. This can be done and continued. The next page offers to enter the settings with the new values ​​of the Wi-Fi network, the name and password of the administrator, click the "Save settings" button.