Communication check atol. Setting up the connection with the offdoc on the fiscal registrar atol. Ethernet communicationOverUSB

To set up data exchange with OFD on ATOL fiscal registrars, you will need to useofficial utility from the manufacturer KKT " Test "POS printer driver”". This utility is supplied in a single archive "Shop equipment drivers", which can be found and downloaded in the ATOL Download Center (section Software -> DTO). After you have downloaded and unpacked this archive, the utility can be found in one of the folders, depending on the bit architecture of the OS and the bit architecture of your computer:

• ... / nt-x86-msvc2015 / fptr_t.exe - for Windows 32-bit
• ... / nt-x64-msvc2015 / fptr_t.exe - for Windows 64-bit
• ... / linux-armhf / fptr_t.sh - for Raspberry Pi
• ... / linux-x86 / fptr_t.sh - for Linux 32-bit OS
• ... / linux-x64 / fptr_t.sh - for OS Linux 64-bit

Option 1 (TCP only)

Run the utility “Test“ POS printer driver ”" and openProperties

Select from the listKKT model

Specify as portTCP / IP

Please enter correctIP address and IP port KKT in the network

Click on Communication check to make sure that the CCP is connected (the result field should display a line describing the CCP model with an indication of the software version)

Open up CCP parameters

V section 18 OFD -> Exchange channel select from the drop-down list the connection type corresponding to your case ( Ethernet / WiFi)

Option 2 (TCP + USB)

To begin with, you need to make sure that the correct Exchange channel with OFD is selected in the CCP settings. For this:

Make sure that this fiscal recorder is not added to the list of Dooglys Connect devices and is not used by any other third-party program.

Run the utility “ Test "POS printer driver”" And openProperties

Select from the listModel KKT

Specify as portCOM port

Click on Communication check to make sure that the CCP is connected (the Result field should display a line describing the CCP model with an indication of the software version)

Open up CCP parameters

V section 18 OFD -> Exchange channel select the appropriate connection type from the drop-down list (Ethernet / WiFi / GSM modem)

In the remaining fields of this section, check the correctness of the connection parameters in accordance with the documentation of your fiscal data operator: OFD server address, OFD server port, OFD DNS, etc.

In this case, the Internet connection of the computer to which the fiscal registrar is connected will be used to transfer checks to the FDO. To set up such a connection, you will need to install and configure a special service on your computer -EthernetOverUsb (EoU), which will receive checks for sending from the connected fiscal registrar and send them to the OFD using the Internet connection configured on this computer.

Before configuring the EthernetOverUsb utility, you need to make sure that the correct Channel for exchange with OFD is selected in the CCP settings. For this:

Make sure that this fiscal recorder is not added to the list of Dooglys Connect devices and is not used by any other third-party program.

Run the utility “ Test "POS printer driver"" And openProperties

Select from the listModel KKT

Specify as portCOM port through which the POS printer is connected to the computer

Click on Communication check to make sure that the CCP is connected (the result field should display a line describing the CCP model with an indication of the software version)

Open up CCP parameters

V section 18 OFD -> Exchange channel select a connection type from the drop-down list EoU

In the remaining fields of this section, check the correctness of the connection parameters in accordance with the documentation of your fiscal data operator: OFD server address, OFD server port, OFD DNS, etc.

Next, you need to download the utility to your computer, which can also be found in ATOL download center (section Software -> DTO -> EoU). After you download and unpack the archive, you will find all the current versions of the EoU utility (we recommend choosing the latest version). In each directory, under the version names, there are distributions of this utility for each supported OS version.

Attention! The methods described below are not the only possible and correct settings. Dooglys is not responsible for the performance of the Atol software.

Windows

The distribution kit for Windows is located in a folder callednt-x86-mingw... Further point by point:

Copy from directorynt-x86-mingw file settings.xml to directory C: \ ProgramData \ ATOL \ EoU(if there is no such directory, then it must be created)

Create a shortcut to the fileEthOverUsb.exe from directory nt-x86-mingw with parameter -e

And 90F, you need to run the KKT Driver Test (included in the drivers, as a rule, you can find it by clicking Start-ATOL - "KKM Driver"), check the "Device is on" checkbox and in the Select mode send a lower-level command 82 01 06 00 to the checkout.

The result of the command will be a check with detailed information about the connection of the cash register with the outside world and the OFD in particular.

Here:
Link- the method of connecting the cash register to the Internet. The options are as follows: EoU - Internet access via the Ethernet over USB service on a PC, Ethernet, WiFi.
USB device- is the USB device connected to the cash register (the command can be sent both via COM and via ETHERNET);
Internet access- the result of the test of the availability of connection to the Internet;
Connection to OFD- the result of testing the connection with the OFD;

What can go wrong when running the command to check the connection with the CRF?

• If the cash register program has not been turned off, the testing utility will not get access to the cash register and the “Device is turned on” checkbox will not be able to be put.
• You will also not be able to access the checkout if the utility is configured incorrectly to connect to the checkout;

What could be wrong when checking the connection with the CRF?

• The root cause is the Ethernet over USB (EoU) service is not configured or started. If the cash register is connected only to a PC via a USB channel, then the EoU service is the only way to send receipts from the ATOL cash register to the OFD.
• Incorrect settings for connecting to the OFD at the checkout - check the port settings and IP address of the checkout in the properties.
• The checkout parameters may contain an incorrect communication channel with the OFD - check it. Also, on some firmware ... you need to set up a WiFi communication channel for the transmission to take place over EoU ...
• If all the settings are correct, there is a connection with the FDO, but the checks are not transferred, call the FDO, it is possible that either you have not activated the data transfer agreement, or the FDO does not accept checks from your cash register for "its own reasons".

The instructions cover the issues of installing the driver, connecting the cash register to a computer via a USB cable and fiscalization of the FN.

When ATOL CKT is connected to a computer via a USB cable, data is transferred to the OFD using EoU (Ethernet-over-USB) technology. The required service is installed with the shop equipment driver (DTO).

The driver "ATOL: KKT with data transfer to OFD (54-FZ) 10.x" is developed in a two-tier architecture and consists of two parts: an integration component (supplied as part of the "1C" configuration) and the main driver delivery (installed via the supplier's distribution kit and usually downloaded from the supplier's website).
The main task of the integration component is to redirect calls from the 1C configuration to the main driver delivery. The basic driver shipment interfaces directly with the hardware.

Installing the Basic Driver Package

Download the DTO distribution kit version 10.4.2 or higher from the ATOL website. To do this, in the download center, you must select the section Software - DTO - 10.x... Download distribution kit Driver KKT 10.4.2.

The archive file in the installer folder contains the files:

1. KKT10-10.4.2-windows32-setup.exe
2. KKT10-10.4.2-windows64-setup.exe

You should run the KKT10-10.4.2-windows32-setup.exe file for execution if you are using a 32-bit 1C client.
You should run the KKT10-10.4.2-windows64-setup.exe file for execution if you are using a 64-bit 1C client.

Connect KKT ATOL to PC.

By default, the channel is set to exchange via USB. If another exchange channel is selected, then to establish a USB exchange channel, do the following:

• Turn off the CCP (if enabled).
• Hold down the check scroll button.
• Without releasing the button, turn on the CCP.
• Release the button after the fifth beep.
• Information with the items of the service mode will be printed on the check. The item is selected by the number of times the scroll button is pressed.
• Select in service mode Exchange channel: press the check scroll button twice.
• Information with the parameters of the exchange channel will be printed on the receipt.
• Select in the exchange channel Usb: press the check scroll button twice.
• Will print on the check USB included, and the KKT will return to the service mode.
• Exit the service mode: press the check scroll button once - the KKT will switch to the operating mode.

Go to Device Manager, find Ports (COM and LPT)... When connected, two COM ports are created.

One virtual COM port is for connecting the KKT, the second is for the EoU data transfer service.

If the COM ports were not found, but 2 "Unknown devices" appeared, then you need to install the driver for them: open the "Unknown device" card, click Update driver and specify the path manually. The default driver path is C: \ Program Files (x86) \ ATOL \ Drivers10 \ KKT \ USB_Drivers.

After installing the driver, the ATOL mark will appear in the name of the devices.

Checking the connection with the KKT

KKT ATOL can be connected to PC via COM / VCOM- or USB-port. When connecting one KKT, it is recommended to select the communication channel via USB. If two or more KKTs are connected, it is recommended to select the communication channel via COM / VCOM.

When choosing a communication channel via USB: in the mode Properties select from the drop-down list the model of the connected CCP and the communication channel through USB... Press the button Communication check.

When choosing a communication channel through COM / VCOM it is necessary to additionally indicate COM port, set the port that was assigned to the device (in our example, COM 4).

COM ports:
atol-usbcom_proxy1 is used to connect KKT,
atol-usbcom_proxy2 - for the EoU data service.
In field Speed the number must be set 115200 .

After pressing the button Communication check in field Communication - Result information about the CCP model should be displayed.

Checking the connection with the KKT via the channel via USB:

Checking the connection with the KKT via the channel via COM / VCOM:

Installing the Ethernet over USB service

Service for work via USB-cable (EthernetOverUSB) is installed together with the driver of the shop equipment.
The port for the EoU is automatically detected. If this did not happen, then you can specify the required port for communication with the OFD in the settings file, which is located in C: \ ProgramData \ ATOL \ EoU v settings.xml... Register the number of the required port, save the file.
In our example, an ATOL USB port (COM5) was created for the EoU, so we write the port number 5:

Important! Folder ProgramData by default has the "hidden" attribute. To see it, you need to open hidden files and folders.

Specifying OFD parameters

Run the KKT driver test: Start - ATOL - KKT driver test.
Open CRE settings, specify OFD parameters: Properties - CCP parameters - 15 CRF - enter the OFD address, the OFD port, select the exchange channel with the OFD - USB (EoU).

Press Apply.

Checking the connection with the OFD

In the KKT driver test, open the tab Lower level... Diagnostics is performed by sending the low-level command 82 01 06 00.
KKT driver test - Lower level- check the box Included... In field Buffer with KKT command to introduce 82 01 06 00 - press the button Execute command.

The KKT must issue a diagnostic check.
The connection of the KKT to the computer is completed.

Connection of CCP ATOL and fiscalization of FN in "1C: Retail"

Create an Instance of the Connected Hardware

In chapter Settings connected equipment ( Administration - Connected Equipment) you need to check the box Use connected equipment.

Then you need to go to the directory Connectable equipment, for this you need to click on the link Connectable equipment, and select the type of equipment KKT with data transmission.

A new instance of equipment is created using the command Create... Create a new element (click the button Create). In the form that opens, you need to check what is installed Equipment type: KKT with data transmission... Next, you need to select the organization on whose behalf the sale of goods will be carried out on this fiscal registrar, enter the name and serial number of the CCP (serial number indicated on the device body). In field Hardware driver select a driver handler from the list. Press the button Write object.

After recording, settings of connection parameters and operations with FN will be available. Also in the window Connecting and setting up equipment the button will become available Tune.

Self-installation of the driver integration component

The integration component of the driver KKT ATOL 10.x is a part of "1C: Library of connected equipment". If necessary, you can add a component yourself.

To do this, press the button Hardware Drivers:

From the downloaded driver archive 10.4.2.zip you need to extract the component 1C... In "1C" we press Add new driver from file- select the archive from the extracted folder of the driver "1C" ATOL_KKT_10.zip and press the save button Write object... Next, click Features - Install driver.

After successful installation, the form will display the driver status - Set and also the driver version.

Setting up a connection to KKT

Press the button Tune... A form for configuring the driver and connection should open. Select Model connected device Port, COM port, Speed specified in the driver settings. Press Device test... A message will appear Test completed successfully indicating information about the connected CCP.

Fiscal accumulator registration

After connecting the KKT to the program, you can register the fiscal drive, if this has not been done before. This operation is also performed when the fiscal drive is replaced after the expiration date or when the memory resource is exhausted - the used fiscal drive is closed, then the physical drive device is replaced and a new one is registered.

To carry out the registration operation, you must select in the program Administration - Connected equipment - CCP with data transmission, open a record with the required CCP. Check the completion of the serial number (mandatory field). To uncover CCP parameters, install Format-logical control method – Split lines, install Allowable discrepancy of format-logical control – 0,01 .

Select item registration from the dropdown list when you click on the button Fiscal accumulator operations.

The registration form will open. It requires: fill in the field Registration number of KKT number received during the registration of the cash register with the Federal Tax Service, check the correctness of filling in the details of the organization, indicate KKT installation address, Place of settlement, choose a taxation system, fill in all other parameters, enter OFD INN and OFD name and press the button Continue operation.

KKT must issue a check on successful registration.

Important! Enabling a parameter Data encryption sign- irreversible operation. Encryption can be an additional service for the OFD, check with the OFD before the fiscalization of the FN.

If it is necessary to change the details of the organization, the parameters of the cash register, replace the FN, etc., it is necessary in the menu Service select Changing the registration parameters of the fiscal accumulator.
Select the appropriate re-registration reason code and set new parameters.
KKT must issue a check on the successful re-registration of KKT

Closing the fiscal accumulator- irreversible operation.

After its completion, the use of FN is impossible.

If the cash register does not transfer data to the OFD, a notification will appear in the operator's personal account “no documents are received from the cash register”.

First, check that the checkout is connected to the OFD. In the section “cash desks” next to the cash desk it should be indicated “connected to the OFD”. If the cash register is connected, but the documents are not received, check the connection with the FDO.

What to do if data is not transferred to the OFD

1. Check the coincidence of the data in the registration card on the FTS website with the data in your personal account. To do this, on nalog.ru go to the "Personal account of the taxpayer", and then - to the "Accounting for cash registers".
2. In the list that opens, select the cashier from which the data does not go to the OFD and click on "RN KKT". After that, the registration card of the cashier will open. Leave it in a separate window.
3. Go to your personal account Kontur.OFD and open the cashier section. Download the checkout list in Excel.
4. Compare the data on the cash register in the file with the card of this cash register on nalog.ru. If the data in your Kontur.OFD account is different, add the cashier to your account again with correct data.

The connection between the cash register and the OFD can be checked through the utilities for the cash register. The instructions are suitable for a cash register that is connected to a computer via USB. If the cash register is connected differently, connect via USB.

Checking the connection with the OFD using the example of the Atol cash desk

1. Right-click on "Start". In the menu that opens, select "Computer Management". Click on it and go to "Services".
2. In the section that opens, select "EOU" or "EOUService" and run. If there is no such service, contact the TEC or the cash register provider for help.

Check CRF settings

1. Open "Start" and in the search box enter KKM and run the utility "KKM Driver". Disable the cash register software to work with the utility without errors.
2. Go to "Property Setting".
3. Select Hardware Options.
4. Go to the OFD section and check the correctness of the settings.
   • The address:
   • IP address: 46.17.204.250
   • Port: 7777
   • DNS: leave it blank or put 0.0.0.0
5. If the settings are correct, write to technical support -