Standard password for DIR 615. Connecting connection in router mode

  • 4xlan 100Mbit \\ s
  • Wi-Fi 11BGN 300Mbit \\ s

Preparation

To configure the router, you will need a login and password issued by the provider.

  1. Take a cable that comes with a router (patchcord). One end will connect to any LAN port, the other end to the computer.

2. Run the browser and in the address bar dial 192.168.0.1 ()

The Routher Settings page opens. Router DIR 615 interfaces can be different. Below, select the one you have:

D-Link Gray

If you do not know what protocol is connected, then try to configure the PPPoE first. In extreme cases, this can be clarified by the provider.

PPPOE D-LINK Setup


  • 1) I choose right at the bottom Advanced settings
  • 2) section Wan.
  • 4) Remove
  • 5) Press the button add
  • 6) choose the protocol PPPoe + dynamic IPOr easy PPPoe
  • 7) We gain login and password Provider issued
  • 8) Apply
  • 9) Upstairs click on Save




PPTP D-LINK Setup

If you have an interface on english language, then you can change the language to the right upstairs:


  • 1) I choose right at the bottom Advanced settings
  • 2) section Wan.
  • 3) allocate all connections if there is
  • 4) Remove
  • 5) Press the button add
  • 6) choose the protocol PPTP + dynamic IPOr easy PPTP.
  • 7) We gain login and password Provider issued
  • 8) Apply
  • 9) Upstairs click on Save




Wi-Fi D-Link Setup

If you have an interface in English, you can change the language to the right at the top:


  • 1) Press advanced settings
  • 2) in the section Wi-Fi Choose basic settings
  • 3) in the field SSID.
  • 4) the rest do not change and click Apply
  • 5) We return to the main menu by clicking on the arrow on the left and in the section Wi-Fichoose Security Setup
  • 6) Install, invent a password of at least 8 characters.
  • 7) Choose encryption AES.
  • 8) Apply
  • 9) Upstairs click System - Save




D-LINK firmware update

The firmware process is very simple. Bap the firmware from the official site. When downloading, pay attention to the revision (indicated on the sticker under the router). It must coincide with the downloadable firmware.

  • 1) go to advanced settings
  • 2) in the section System Click arrogant right
  • 3) click on Software Update
  • 4) Indicate way To downloaded firmware
  • 5) Press refresh.


D-LINK AIR

PPPOE D-LINK Setup

  • 1) We choose on the left Net -> Wan.
  • 2) allocate all connections
  • 3) Remove
  • 4) Add New connection
  • 5) Choose PPPoe + Dynamic IP or simply PPPoe
  • 7) Apply
  • 8) upstairs System -> Save

PPTP D-LINK Setup

If the interface is in English, then it can be changed in the menu above:

  1. 1) We choose on the left Net -> Wan.
  2. 2) allocate all connections
  3. 3) Remove
  4. 4) Add New connection
  5. 5) Choose PPTP + Dynamic IP or simply PPTP.
  6. 6) We recruit credentials issued by the provider.
  7. 7) Apply
  8. 8) upstairs System -> Save

Wi-Fi D-Link Setup

If you have an interface in English, you can change the language to the right at the top:

  • 1) on the left in the section Wi-Fi Choose basic settings
  • 2) in the field SSID. Invent the name wi-Fi network (Latin)
  • 3) Do not change the rest and click Apply
  • 4) on the left in the section Wi-Fi Choose Security Setup
  • 5) Install network Authentication - WPA2-PSK, invent password at least 8 characters. Encryption choose AES.
  • 6) Apply
  • 7) Upstairs click System - Save


D-LINK firmware update

ATTENTION! Updating the firmware can lead a router into a non-working condition. The probability is very small, but it is. Download firmware only from official sites.

The firmware process is very simple. Bap the firmware from the official site. When downloading, pay attention to the revision (indicated on the sticker under the router). It must coincide with the downloadable firmware .Save setting and wait until the router reboots

PPTP D-LINK Setup

  • 1) Choose MANUAL Internet Connection Setup
  • 2) My Internet Connection Is Select PPTP RUSSIA DUAL ACCESS or simply PPTP.
  • 3) Introduce login, password and PPTP Server Address Provider issued
  • 4) Reconnect Mode Choose Always
  • 5) Save the settings Save Setting. and wait until the router reboots

Wi-Fi D-Link Setup

  • 1) Select Wireless Settings
  • 2) Select Manual Wireless Connection Setup
  • 3) Wireless Network Name is the name of your home WiFi network
  • 4) Security Mode Select WPA Personal
  • 5) WPA MODE - Select WPA Only
  • 6) Pre-Shared Key - Come up with a password for a network of at least 8 characters.
  • 7) Save settings - Save Settings

D-LINK firmware update

  • 1) Upstairs in the menu select Tools
  • 2) left in the Firmware menu
  • 3) Indicate the path to the firmware
  • 4) UPGRADE - run the firmware of the router.

The D-Link DIR-615 setting has not yet been described as detailed as this time. In this publication, we will consider how to set up a fairly common router of the company D-LINK DIR-615. In the article I will refer, as an example, on D-Link DIR-615 / a. But even if you have a router of another brand, not fundamentally, because in many ways the settings are identical to all. Therefore, this manual is applicable for most D-Lіnk models. I will try to put everything in detail and affordable.

It is not possible to describe the features of the router itself for a long time, if necessary, you can read about DIR-615 / A if you follow the link located slightly above. I will only note that this model copes perfectly with its functions of the house, or in not too large offices. With it, uninterrupted Internet is served on computers, tablets, wireless telephones.

By part of the setting of D-Lіnk DIR-615, it is fairly easy to implement. Provided that your Internet provider applies a connection method of a dynamic ip, then you just need to connect and turn on the router, and the Internet access will be available. It will only be necessary to put a secret code on the WI-FI, and change the name, if necessary. The only thing that does not suit me is that almost all editions change (visually) setting the D-Lіnk parameters, that is, the control panel. Thus, the settings of your router may not look as shown in this publication. Although it is fixable, just need to reflash it.

We act according to the following scheme:

  1. Connect the router and enter the D-Lіnk DIR-615 settings page.
  2. Configure an Internet connection on the router
  3. Configure a wireless network and change the password combination.

And now consider each of the stages in more detail.

Connect the D-Lіnk DIR-615 and go to the settings

Turn on the router, initially connecting it to the power source. Provided that the indicators did not light up in the foreground, it is possible that the power button is turned off. In case setting D-Lіnk DІR-615will be carried out through the cable, find the power cord, and connect the access point to the computer (the cable is sold as part of the router). One side of the cord is connecting in Lan.black connector (in first four), and connect another to network adapter Laptop or computer. Internet cable should be inserted into Wan. The connector that is painted in yellow.

In case there are no cord, or a computer with a network card, you can make settings using wireless network. In this case, even the phone or tablet is suitable.

Connecting a router to a wireless network for adjusting

Make an Internet connection under the usual name"DIR-615"

It can stand protection. In this case, use the password, which is indicated at the bottom of the router

Then you must open the control panel of the router. But before, I recommend, reset all existing settingsIn order to establish them, they did not fail. Thus, our router will customize "with a clean sheet".

Reset settings on D-Link DIR-615

It is not difficult to reset the settings. To do this, take a sharp object and using it to press the button Ryset,which is slightly deepened in system buildingand a little wait. Then stop pressing and wait for the router reboot.

Enter any Internet login program and transition to the Internet address 192.168.0.1. The window will populate in which the login and secret code will be requested. If you have not changed this data, then you gain admіn.both rows and opens the control panel page of your router.

It may be that the settings there will be in English, which can be easily changed to a more suitable and understandable (Russian, Ukrainian).

Also, the window can also jump out, which indicates the initial password, with which the input is in the D-Lіnk control panel. Then enter any cipher invented by you and repeat the same in next line. And be sure to remember, or better write, as it will need to be entered each time the router settings.

I recommend you immediately before tune, download new software on your D-LINK. Read in detail how to do it, you canthis article . But you can configure further and without firmware, if we say it will be hard to do it.

After entering the password, we immediately entered the settings, you can now configure the router.

The annoyance of the Internet configuration process on the D-Lіnk DIR-615 router

  1. First of all, it is necessary learn which connection technology uses your provider. Active IP address, fixed, PPPOE (Practicing House.RY, and other Internet providers), L2TP (Applies Beeline). In my articles, I told how to find out the connection technology. It is possible to learn this information on the main website of the provider, or even call the company.

Provided that your Internet connection is made according to the widely used method of dynamic ip, the router must distribute the signal as soon as the wire from the company will be connected to it. Then you will need to simply make the wireless network settings (how to do this later). If you have a static ip address, then you will be configured.

  1. Find the tab Start— Click'n'Connect.. Check the Internet connection - Cable and select Further.
  2. From the list that appears, find the desired connection. If, let's say, your PRPOE connection, and another Internet provider gives in addition to this, then we make the choice of PPPOE + static ip. Provided that the ip address is not provided, then we put the selection icon opposite PprOe + dynamic IP. Similarly, we do if the connection is L2TR.
  3. Next, specify the data of the IP addresses, if it is provided to you (otherwise this window will not). And press the button Further.
  1. Further, the "Address of Local Resources of the Provider" can be opened. If you do not know what it is, or you just do not want to make additional addresses, then click Further. Retires the window with a query of the connection name and user, and input and confirm the password. This data gives your Internet provider. In order to make more settings, go to the tab detail

Then an Internet connection and the reality of the Xandex selection will be inspected. But it is already if you want. All the same settings can be changed.

The settings on the example of PROE for the D-Link DIR-615 router are considered. Your settings may be different.

If you configured the access point, and in the end there is no Internet, it is displayed "without access to the Internet", or there is no access to the pages, then this problem is related to the settings from the provider company. Check, it may incorrectly indicated the type of connection, or any other data.

Therefore, with a compound PPPoe, PPTP, L2TR and dynamic IP is more complicated than the static ip connection method.

Very important! Provided that earlier you went online with high-speed data exchange, now you are, in fact, there is no need. Such an Internet - the connection will carry out your router and only distribute it on a wire and wireless network.

Change the settings from the provider using the same CliSk'n'Connect, or by clicking on Net —Wan.At the same time, having selected and change the required compound.

Provided that everything is in order, and the Internet connection through the router is available, then go to the installation of the wireless network parameters.

Visual example of setting Wi-Fi and changing the password combination on D-Lіnk DIR-615

Now we will need to simply change the name of the wireless network, and come up with another secret code for the security of the WІ-FI connections.

Become on WІ-FI - basic settings. Here you can change the name of our wireless connection. In line SSID.enter the network name - Internet, and select Apply.

Next, open the menu Wi-Fi — Security Settingsand in the string "PSK encryption key"we enter the code, it will be further applied to connect to the WI-FI network every time. The secret password must contain at least 8 characters. Remember, or somewhere write it, so that you do not forget

Molded settings must be saved. System - Save. This may be the final stage of setting up the router D-Link DIR-615. If no settings

you will no longer exercise, then make it reboot. The system is to restart.

Now the WІ-FI network is configured. In addition, you may need to see more details on setting up Wi-Fi.

There is also an opportunity to change the adminipol, the use of which is needed to enter the router settings. To do this, use the tab System - Administrator password.

Enter the invented code twice and select the button. Apply.Made actions be sure to save.

Remember either make an entry secret Code.So as not to drop all the settings again, since without a password, the entrance to the control panel will be unavailable.

Wireless Router D Link DIR 615 is a convenient "home" router, providing Wi-Fi connection at a speed of up to 300 Mbps according to 802.11b, G and N.

Externally, the model is a "classic" stationary Router with two external antennas and cable connection connectors external devices. From the functional features, you can mark the built-in network screen, the ability to work with SIP protocols and support for all wireless communication.

D-Link DIR-615 provides a stable Internet connection when working with such providers, like Rostelecom, Dom.ru, MTS, Beeline, etc. Also, the device can be used to connect to the worldwide network by dedicated line and Dial-Up technology - in this case it will be necessary additional setting modem.

d LINK DIR 615: Specifications

wiFi. router dir. 615 operates in the frequency range of 400 ~ 2483.5 MHz.

On the rear panel of the device there is one Internet port for connecting the Ethernet cable provided by the Ethernet provider and four LAN connector to connect to the router, and other stationary devices through a power cable.

The DIR 615 modem supports functions and static IP routing.

On the front panel of the DIR 615 there are indicators of the router status:

  • - separate "standing" power indicator;
  • - Internet connection activity indicator (if this LED is not lit - it means the Internet from the provider to the router does not come: perhaps a lines of the line or technical failure of the service provider);
  • - WiFi indicator, the green light of which characterizes the ability to connect to the ROUTER D LINK DIR 615 for wireless communication;
  • - four LAN indicators that are burning with the activity of the corresponding LAN connector;
  • - WPS indicator, which lights up when activated.

How to connect the D LINK DIR 615 router?

Installing the router D LINK DIR 615 is carried out according to the standard instruction identical for most network devices.

  1. 1. First provide "food" of the device from the standard power grid 220V. To do this, connect the power adapter plug to the round connector on the rear panel of the device, and the "plug" of the adapter is to any AC outlet.
  2. 2. Turn on the router using the ON / OFF button and wait for the router OS boot - the corresponding indicator should light up on the front panel of the Device.

If your router was ever in operation, it is recommended to pre-reset the D LINK DIR 615 settings to factory. To do this, it is necessary to press the Reset button with a needle or closure to press the RESET button, delay it until 10-15 seconds and wait for the device to reboot.

  1. 3. For the primary setting of D LINK DIR 615, you need a "hard" connection of the router to the computer. For cable connections, you can use the patch cord or a twisted pair, cut from two sides by the RJ 45 connector, and the network cable must be connected to any LAN connector on the back of the router, and on the other - to the port network card Your inpatient computer or laptop.
  2. 4. To connect D Link DIR 615, the corresponding settings of the computer network card will also be required. Step-by-step instruction For Windows7 and Windows8, it is presented in the article, and setting up network settings on Windows XP is step-by-step written in the article.

How to independently set the router D Link DIR 615?

Configuring the D LINK DIR 615 router occurs through the device's web interface, while entering the menu with a computer connected to a router via any web browser.

To do this, enter the static IP address of the device in the address bar (in most cases it is a combination of 192.168.0.1), which is specified on the device's service label.

Press ENTER and in the authentication window that appears, enter login and standard password DIR 615.

Router D Link DIR 615 Password Default - Admin and Login - Admin. If the settings have been changed, and the user subsequently forgot the router password - it suffices to reset the device settings to the factory and enter a standard password.

At the first stage, the Internet is configured through the D Link DIR 615 router. For this you need to clarify:

  • - What type of Internet connection to you provided a provider;
  • - is it necessary when connected to global Network specify a login / password;
  • - What parameters "on the Internet" provided you with a communication service provider.

These parameters are specified in the contract with the provider, as well as their clarification in 24-hour service Support provider.

If this window already has an automatically generated WAN connection - it is recommended to be removed.

  • - for PPPOE connection In the discontinuing PPP subsection, enter your login and password to connect to the Internet from the contract with the provider;

  • - To connect a static IP address, you will need to specify the IP address, a network mask, the IP address of the gateway and the primary DNS server (also from your contract);

  • - For dynamic IP in the Count IP, remove the marker with "Get the DNS server address automatically" and enter the Primary DNS server provided to you.

Wireless Router DIR 615: WiFi Setup

WiFi Setup on the D LINK DIR 615 router is carried out in the corresponding menu tab:

In the main window of the router settings, click the Wi-Fi button and go to the "Security Settings" section.

Please note the complex and unique password on Wai Fi for wireless security purposes.

Router DIR 615: IPTV Setup

For iPTV connections On the Wireless DIR 615 router should:

  1. 1. Turn on the TV console in the free LAN port of the device.
  2. 2. In the LC select "Advanced Settings" and heading "IP Television".

  1. 3. Select the corresponding port of the device in the "IPTV settings" wizard and click the Edit button.

At this setting of IPTV successfully completed.

Connect your home to the Internet is very simple and most often even cheap. However, not all Internet companies provide the setting of the router for you. Therefore, the first user, the buyer, has to independently configure the router.

So that no problems arise in the setup, just follow our simple instructions by setting up D-Link DIR-615.

Characteristics and appearance of the router

Regarding the characteristics of the D-Link 615, it is almost nothing to say, for all such devices are extremely similar to each other. Used 802.11n technology, built-in antennas, 4 network Port., work frequency is about 2.4 Gigahertz. Data transfer rate through a cable up to 100 megabits per second, through a wireless network up to 300 megabits per second.

On the front panel there are several, and if more accurate, 8 light bulbs performing the role of indicators:

  • The first indicator "Power", this light bulb is responsible for the diet of the device, connecting to electricity.
  • The indicator signed "WPS", it shows the status of this function.
  • LIGHT "INTERNET". It is not difficult to guess what she answers. This is a state of connecting to the World Wide Web.
  • The remaining indicators are responsible for the ports. The first of them "WLAN". This WiFi mode.
  • Another 4 connections through the LAN cables.

On the side panel there is only one WPS button that can quickly connect.

On the back panel there are two special places for fastening our device to the wall. And below are different ports and buttons:

  • First go 4 local ports where you can insert a network cable for connecting home Computer directly.
  • One port for connecting the Internet.
  • The button located inside the opening "RESET". To press it, you need to use some kind of thin object, for example, a clip. Click this button for 7-10 seconds. After the device is restored to the factory settings.
  • Power connector router. You need to insert the power cord, which the other side should be in the outlet.
  • Routher power on / off key. Using this button you can restart the router.

After we exactly learned the location of all the connectors you need and indicators, you can go to the installation rOTETER D-LINK DIR-615, I will perform the setting a little later.

Installing a router in place

Choose a place that would be about in the middle of our house or apartment. This is in order to be about the same signal in different rooms. Nearby should be a socket and there must get the Internet cable.

We attach it to the wall, insert the power supply, turn using the power button, connect a laptop or computer to it via LAN port. Here there is another moment, important in further configuration. If the Internet immediately appeared on the computer, it is possible to determine which IP address from your provider.

If the Internet immediately appeared, then you have a dynamic IP address. On the WLAN wire, the provider incoming traffic is immediately redirected to you.

Questions how to connect or how to install a 615 router for Rostelecom, it should not occur because each connector meets its wire.

To make a static IP, you need to execute the D-Link ports 615 ports. Move directly to the settings of the Link. About how to open ports on the D-Link router, we will write in a separate article.

Complete configuration of Device

To begin with, immediately after connecting the router 615s to the computer, it is worth resetting the settings. So, to set up D-Link DIR-615 from the very beginning:

Reset

To reset the settings you only need to press the "RESET" button located with back side Apparatus in the hole. Press the key for 7-10 seconds. All D-Link DIR-615 router settings will become factory. This is a particularly important step for those who bought the device after someone's use.

Also reset can be done by those who forgot the password. To put the password and the default login on the router Wi-Fi D-Link. After reconfiguration is performed.

Problems of firmware

After that, it is worth noting that on routers usually costs old version Firmware, the most ancient. You can also work with it, but it is better to take care of your nerves and forces - download the update. Download yourself new firmwareTo keep up with the whole world.

On the bottom of our device there is a serial code and a bunch of other updating information. We are interested in the line "H / W VER. :**". There should be a version of your D-Link DIR-615 router on the site of the stars. We have this K1.

Now, before entering the settings, go to the official website http://ftp.dlink.ru/pub/router/, we do everything clearly in screenshots. Here is an example update to K1.

Now we have software for our router that we needed to update. Now, in fact, learn how to flash the D-Link DIR-615 router.

To do this, you need to go to the settings to the router debugging site in the router settings, this is address 192.168.0.1 or 192.168.1.1. Enter the name and password - "Admin" is the factory settings of the router D. Now you can see the interface. The firmware version is written on top. If this is version 1.0.0, then go to "configure manually". Then "System", choose "Update software", Choose the file that was downloaded a little earlier and updated the modem.

On this flashing is over.

Debugging Connections to Web

We go into the same router settings at 192.168.0.1, enter Admin / Admin, click "Login". In the updated firmware, press the advanced settings below. Then chose WAN in the list, this item is located in the "Network" block.

Press the "Add" key, thereby creating a new network connection. Here you need to enter the data that the provider provides you. Connection type, login and password must be specified in the contract, do not forget to clarify these moments from him. It is necessary for connecting to the Internet. Click "Save".

Now the Internet should appear local networkThat is, on those computers that are connected via LAN local cords.

Debugging wireless network

In the "Wi-Fi" block we click on general settings. All this is in the same extended settings if anyone forgot. Here click "Enable wireless connection", We put a tick and save. As you can see, setting up the Wi Fi router D-Link DIR-615 is a fairly simple task.

After that, in the SSID field, we enter the name of your wai fi, it will be visible to everyone. Write in english. We choose our country, the channel is automatic and the mode is the same.

Now B. wi-Fi block Select security settings. In the first paragraph wiFi settings We put WPA-PSK2. In the next field where the encryption key. This is a password from Wi-Fi. On the same tab, the answer to the question is how to change the password or how to put a password on Wi-Fi.

Now you have figured out how to configure the D-Link DIR-615 router thanks to our step-by-step instructions.

Video on the topic

Quickly you internet!

In this instruction, step by step, consider the process of setting up a wireless router to work with wired home Internet from Rostelecom. Guide is suitable for all recent revisions. Wi-Fi Router:

  • DIR-615 M1
  • DIR-615 K1 and K2

How to connect router

The correct DIR-615 connection scheme in order to continue to access the Internet, all connected devices are as follows:

  • Internet cable Rostelecom connects to the Internet Cable Rostelecom
  • If there is a TV prefix, it should be connected to one of the LAN ports
  • A computer or laptop from which you set up connect the included cable with one of the LAN ports to the Wi-Fi router. Initial setting More convenient to produce wired connected. However, if this is not applicable to your situation, you can configure both Wi-Fi.

Well, after the actions described above, turn on the router into the outlet.

How to go to the router settings and configure Rostelecom PPPoE connection

Note: If you have previously launched a Rostelecom or high-speed connection on the computer, disconnect it at the setup time and do not connect it after it: the router itself will install this connection. If it is running on the computer, then there will be no other internet devices.

In order to go to wi-Fi settings D-Link DIR-615 router, Run any browser and enter in the address bar 192.168.0.1, on the page that opens you will be prompted to enter a login and password to enter the router settings . (If nothing opens at the specified address, see).

Standard login and password for D-Link DIR-615 M1, K1 and K2 - Admin and Admin, respectively.

After the correct entry, you will find yourself on main page The DIR-615 settings (if you "threw" again on the login and password window, then they were entered incorrectly, or changed earlier: if you do not know them, reset the router to the factory settings).

At the bottom of the page, click "Advanced Settings", after which, in the Network section, click on the "WAN" link.

A page with a list of connections will open in which one single connection will be connected to the dynamic IP address. Click on it with the mouse, and you will fall into the settings of this connection, which should be changed to work with the Internet Rostelecom.

You must enter the following parameter values:

  • Connection type - PPPOE (it is Rostelecom that uses it)
  • Username - Login for Internet Rostelecom.
  • Password, password confirmation - password for entering Rostelecom.

Click the Save button. After that, a page with a list of connections will open again, and the newly modified will be "broken". Also at the top of the page you will see the indicator that informs that the settings made must be saved. Do it.

Now update the page with a list of connections and, if everything has been done correctly, you will see that the connection status has changed to "connected". Now the Internet on the computer is available.

How to put a password on Wi-Fi on D-Link DIR-615

The following task is to install an SSID (wireless network name) and password on it. How to do this can be seen in the video below, where it is shown in detail (although video for DIR-300, all actions are completely similar).

Configure TV Rostelecom (IPTV)

To configure the Rostelecom television, on the main page of the router settings (not in extended), select "Master iPTV settings"And specify the LAN port to which the TV is connected. After that, just save the installed installations.