Setting up a zte f660 mgts router: step by step instructions. How to set up a modem ZTE ZXHN H108N Zte router login

The ZTE ZXA10 F660 router is a modern network equipment required to connect to the worldwide information network via a fiber-optic line (GPON technology). In terms of its functionality, it is both an ONT terminal and a Wi-Fi router, capable of distributing the Internet both via an Ethernet cable and wirelessly with an end device.

In addition to the standard features of the zxa10 f660 router, it also provides IP telephony and the ability to create a local Web server based on the router.

And this article provides step-by-step instructions for setting up a zte zxa10 f660 router from mgts, and also discusses some of the subtleties of connecting this device.

Router zte zxa10 f660: specifications and design features

The gpon ont zxhn f660 router is an economical mobile Wi-Fi transmitter with a main operating frequency of 2.4 GHz.

The functionality of the router provides Wi-Fi data transfer rates up to 300Mbps, while the device supports up to 4 SSIDs with 128 simultaneous connection of users to each network.

Also, the zte f660 router supports WPS mode, so the device can be used to expand the WiFi zone of another router.

On the back of the router there are:

  • - standard LAN connectors for connecting to zxa10 f660 devices via an Ethernet cable;
  • - two POTS connectors for implementing the IP telephony function (for connecting an RJ-11 telephone cable);
  • - two USB connectors for connecting external media (including for updating the firmware of the device and organizing a local Web server);
  • - POWER connector for connecting a power adapter;
  • - on / off buttons for WLAN and WPS functions;
  • - RESET button to reset the router settings to factory defaults;
  • - button to turn on / off the router.

The GPON connector for connecting a fiber-optic cable provided by the provider can be located both on the back and on the side of the zte f660 router.

Connecting the zte f660 modem

1. Connect the power adapter (supplied with the device) to a 220V electrical outlet, and its plug into the socket on the rear panel intended for it.

2. Connect the green plug to the optical cable port and the other end to a power outlet.

3. Insert the plug of the patchcord (Ethernet cable) into one of the four LAN sockets, and its other end into the network card connector of the computer, from which the MGTS gpon zte zxa10 f660 router settings will be entered.

When the router is connected to a PC, the indicator corresponding to the active LAN connector should light up on the front panel of the device. If this does not happen, it is recommended on this computer.

How to set up zxa10 f660 router?

Connection, testing and configuration of optical communication, as a rule, are carried out by specialists of the company-provider of communication services.

If you are installing the zte f660 optical modem by yourself, then call the service provider of the provider, ask to set up the equipment and follow the instructions of the specialist.

Zte zxa10 f660 router: WiFi setup

1. Launch any Internet browser installed on your computer and enter http://192.168.1.1 in the address bar.

In the field that appears, enter the login: admin, password: admin and enter the configuration interface of your device.

2. A menu with tabs will appear in the window that opens: “Status”, “Network”, “Security”, “Application”, “Administration”.

3. Go to the "network" tab, in the "WLAN" submenu and its subsection "Basic".

In the column "Wireless RF Mode" select the option "Enabled".

  • - Next, "Mode" should be set to "Mixed802.11b + g + n".
  • - "Country / Region" - "Russia".
  • - "Chanel" - "Auto".
  • - "Transmitting power" - "100%".

4. Click the "Submit" button, then go to the "Multi-SSID Settings" subsection.

In the “Choose SSID” box, select “SSID1”.

  • - Check the “Enable SSID” checkbox (Make sure the checkbox is unchecked for other SSIDs).
  • - Come up with a name for your network and write it in the "SSID Name" field.

5. Press the "Submit" button again and go to the "Security" subsection.


- Here in “Choose SSID” select the first option.

  • - Set "Authentication type" to WPA2-PSK.
  • - Create a password for the Wi-Fi network and enter it in the “WPA Passphrase” field.

The password must be unique and contain at least 8 Latin characters. It is not recommended to set standard and easy-to-guess passwords (for example, home address) in order to avoid unauthorized connections to your WiFi network.

How to change the password from the mgts zte f660 router?

To set a unique administrator password used to enter the settings of the MGTS gpon zte zxa10 f660 router, go to the Administration menu and the User Management submenu.

- Switch "User Right" to "Administrator".

Enter the old password in the “Old Password” field, and the new password in the “New Password” and “Confirm Password” fields.

It is also recommended to disable the WPS function before using the zte f660 router. To do this, press the corresponding button on the back of the device.

ZTE routers are known to Russians. Megafon provides subscribers with mobile options that only catch the cellular network. The reception speed reaches 150 Mbps. The modem distributes wireless internet. The portable option is often the choice of remote relatively small settlements. Residents of Udmurtia are now familiar with MR150-5. A region north of which there are only forests and tundra.

Chinese products from ZTE are distinguished by their relatively low cost and availability. Even the prisoners appreciated the advantages of 4G mobile communication. Recently, attackers tried to transfer 29 ZTE routers to the Tula colony. Valiant law enforcement officers managed to prevent an illegal transaction. Let's see how exactly the router is configured. Often the audience is interested in the instructions for changing the password.

ZTE at a glance

In addition to routers, mainly mobile ones, supplying subscribers with a network from Wi-Fi, the Chinese corporation supplies a full range of user equipment, including IPTV digital television set-top boxes. More than half of the manufactured products are serviced by provider networks. Many Chinese telecommunications service providers now use domestically produced equipment.

The history of ZTE is over 30 years old. One of the investors was the Ministry of Aerospace Industry of China. Initially the main income came from consumer goods, but the booming communications industry has loaded a state-owned enterprise with orders for cellular CDMA networks. In 2006, 40% of the company's revenues came from operators' equipment. In parallel, offers from foreign companies fell in. The first was the Canadian Telus.

A year later, the Chinese equipment was ordered by Vodafone (Great Britain), Telefonica (Spain), Telstra (Austria). The 2008 client base included customers from 140 countries. ZTE ranked third in the GSM communications equipment market (about 20% of global sales). The company gradually mastered the production of smartphones. The corporation's engineers have filed over 48 thousand patents, in just two years (2011-2012) 13,000 were confirmed.

Sometimes the company's equipment does not work ...

Define name

The first step is to determine the true name of the device. For example, providers call MF920W as follows:

  1. MTS - 835F
  2. Yota - MF920
  3. Megaphone - MR150-5

A thorough study of the issue will help you choose the right firmware. An incorrect version can cause the device to malfunction. Such hardware does not turn on, a flashing will be required. By the way, studying the forums in advance will show the potential buyer the current problems of the model. For example, the one mentioned above is often devoid of a charger, there is no antenna output. Therefore, choose a different model for giving. An added bonus - the modem refuses to identify the amateur flashing utilities.

The nuances noticed by users will sometimes become the main criterion. A sales clerk interested in sales is unlikely to advertise the dark side of equipment. For example, MF823 requires a Beeline card with a USIM sticker. Otherwise, 3G technologies are used instead of the fourth generation. There are no updated firmware versions.

Common problems

Saving the time of the readers, the caring admin installed a plugin that draws convenient navigation according to the generated tree of subheadings. Therefore, we will devote a separate small section to each problem. ZTE mainly manufactures mobile modems, sometimes supplementing the GPON with a fiber optic line interface.

Does not turn on

First of all, we remember whether the flashing was carried out. Unsuccessfully performed manually - the operation removes access to the router completely. It is noteworthy that the appearance of the device (indication, backlighting of the Ethernet interface) is the same. However, it is impossible to connect a PC to the router, the equipment is impossible. The browser writes: Unable to connect.

The hardware reset button is powerless to solve the problem. The firmware needs to be updated. Trustworthy manufacturers supply specialized utilities to help savvy technicians solve a problem. However, the Chinese manufacturer has been keeping quiet for now. The hackers released the ZTE Unlocker utility, but the interface deals exclusively with the issue of unlocking (decoupling from a specific provider). The software actively exploits the diagnostic port specification.

A healthy device understands the terminal language, including the Windows command line. The operating system allocates a virtual directory to the device, inside which the commands stored by the router's memory are executed. For example adb shell. However, the standard control paths will refuse to help restore the firmware on the router. Enthusiasts suggest the following option.

Sometimes the desire to unblock is caused by others. For example, the developer removed support for the H108N model for FTTB protocol. All users of the interface were forced to rollback immediately. Only now ... the manufacturer has posted one utility - the one that makes the upgrade. One way ticket.

Recovery utility

Often a broken ZTE modem is detected by the diagnostic interface. The official website (ztedevice) provides owners of the MF30 (Beeline) exclusively with the update utility. There are no other models at all! The site 3ginfo.ru offers those who wish to download: "ZTE MF30 Recovery Kit".


Now the folder containing the previously unpacked firmware image needs to be corrected. The software read the device memory by correcting the contents of the internal directory. However, the utility is powerless to enter IMEI. Therefore, edit the Channel1.nvm file yourself. Enter the correct IMEI.

Now run any flashing utility (for example, 3ginfo.ru/downloads127.html). Upload files to the program, including the edited Channel1.nvm. The router is now completely rebuilt.

A similar sequence of actions helps to reanimate some other mobile hotspots (for example, the MF90).

JTAG

Many killed devices are helped to bring back life. Let's briefly describe the essence. In the 1980s, integrated circuit switching standards were deprived of a debug interface. Therefore, in 1985, a special JTAG group was created to solve the problem. The industry standard went commercial (IEEE 1149.1-1990) in 1990. Intel immediately provided the 486 generation of processors with a debug interface.

Nowadays, the standard is used by electronics manufacturers everywhere. Initially, the interface was for testing purposes only. Then the opportunity interested debuggers, including the machine code layer. Later, manufacturers figured out how to exploit JTAG by updating the firmware of flash memory chips. Real boards use the number of pins:

  • 5 and so on.

The latter options are more often used in the presence of many parallel-connected microcircuits. The first option accompanies a star topology. Therefore, the problem is limited to calculating the location of the JTAG port pins. Modern interfaces often contain 10 or more contacts, so take the trouble to find technical documentation that reveals the meaning of the contact pads. The contacts themselves are round or rectangular, often located along the edges, sometimes in two rows.

The pinout is difficult to find, since the subject is the bread of the repair shops. Try to puzzle thematic forums (for example, gsmforum.ru). You will also need a full memory dump, take, for example, here w3bsit3-dns.com/forum/index.php?showtopic=255231&st=3040#entry36468746. The current memory dump (in reserve) is merged with the H-JTAG utility. An adapter connector will be required (the type is entirely determined by the utility used for recovery). Craftsmen usually adapt the now obsolete LPT. Solder the adapter with shunt resistors, get specialized software (for example, Z_Flasher Reanimator is used to restore cellular USB modems).

The Giveio memory dump helps you figure out the processor type. This will be needed later when flashing. So, for work you need:

  1. A utility for backing up the current memory dump.
  2. Compatible modem firmware version. Try to go to byfly. The FTP server provides a specific choice: H208N, ZXHN H208L, H201L, W300. By the way, the Belarusians have taken the trouble to put a set of a novice resuscitator, including instructions, in the shared folder of the server (ftp.byfly.by/byfly/firmware_modem/ZTE/).
  3. A utility for flashing through the JTAG interface.
  4. Hand-assembled connector. Detailed requirements for the adapter are set by the utility. Above was an example of using LPT.

Along the way, they exploit the capabilities of the auxiliary software. For example, determining the type of processor.

Doesn't let in settings

A live router is accessible through a browser or remote administration interfaces (TelNet, SSH). However, the admin panel does not launch inside. The factory settings have probably been changed. After making sure that the provider's password has been written down, try resetting the device with the Reset key (otherwise, you will lose the Internet until your mother arrives). Then the previous characteristics of the equipment will return:

  1. IP address.
  2. Login.
  3. Password.
  4. SSID, Wi-Fi security key.

Refuses to share wifi

Ukrtelecom subscribers flooded TP with complaints: ZTE H108L refuses to connect wireless (wireless) subscribers. You will need to change the settings.

  1. Open the admin panel (192.168.1.1 in the browser).
  2. Enter your username / password (admin).
  3. Click Administration → System Management → Restore Factory Settings.
  4. Apply changes, wait for reboot.
  5. Re-enter the username / password for the ADSL connection.
  6. Set the following settings on the Administration → TR-069 page:
    1. ACS URL - https: // localhost
    2. Login - loose
    3. Password - 12345678

Port forwarding

It is often required to puzzle a home PC from the outside, organize a server. Network protocols use communication ports polls. The modem was originally designed to protect against hackers. Access to the inside (Intranet) is completely absent. Therefore, the port availability needs to be configured. Let's demonstrate the tuning technique using the H118N example.

Note. The specified model shares Ethernet. The previous one (H108N) is equipped with two interfaces: FTTB, ADSL.

The easiest way to defeat Rostelecom's hardware is to use the built-in Application menu. Activate the UPnP subsection. The port number is specified by a digit. A little below the specialized section is located. The Port Forwarding menu will help you to set the necessary numbers. Take the trouble to check the Enable box.

The third way is to set up a DMZ. Creating a dedicated service helps limit the damage of a potential hacker attack. The settings are the same:

  1. Connection type + port (in one line).
  2. Local IP address of the PC.

Note. Port forwarding is sometimes called port forwarding by interpreters.

Pre-test the functionality of the externally provided service within the network. Helps reduce setup time.

Unlocking

It happens that sometimes the subscriber wants to change the provider. I bought the MF823D, I was impatient to switch to Iota, or I got tired of MGTS, and the F670 refuses to eat someone else's SIM card. To change the service provider, you need to unblock the hardware. Megaphone MF823 calls M100-3 - the essence is the same. Unlocking is closely related to flashing issues. A binary image that is not tied to a provider is selected.

Attention! Study the forums carefully before flashing. Some homebrew versions of the software partially interfere with the functionality. Example - H118NV2.0.1d_E04_OV DOMRU removes the web interface (via a browser). Telnet access remains. You have to reflash.

Instruction: Model MF823D

You will need a firmware image. Get it using search engines.

  1. Downloading the PuTTY terminal emulator.
  2. Install the ZTE diagnostic mode driver.
  3. We turn on the equipment.
  4. Feed the browser a convoluted link 192.168.0.1/goform/goform_process?goformId=MODE_SWITCH&switchCmd=FACTORY.
  5. The modem will send a response containing the line OK.

The iron should go into diagnostic mode. Check by opening Windows Task Manager. The properties contain the serial port number, opposite the corresponding COM there should be an inscription ZTE Diagnostic Interface.

Open a PuTTY terminal, copy the image to the serial port, the number of which is shown by the task manager. It remains to release the device from the diagnostic mode. Open the terminal again, set the mode parameters:

  • Protocol - Serial (serial port).
  • COM line number (as per Task Manager information above).
  • Try to set the speed to 921600.

The terminal window will be completely blank. Hammer the commands one by one, each time I press Enter:

  1. AT + ZCDRUN = 8
  2. AT + ZCDRUN = F

Each time, a device response may occur containing the number of successful, failed operations. The operation is over. Reboot your device.

Modem ZTE MF90 +

  1. Install the router following the instructions in the instructions.
  2. Open the admin panel through a browser (m.home, or the IP address specified by the manufacturer).
  3. We configure access to Wi-Fi. Open the web interface (by entering the admin login / password). Leave one device in this position. Later it will be possible to use the graphical shell, although the PC connected with the cable will stop opening the menu.
  4. We feed the browser (via the cable) the translation strings to the diagnostic mode: m.home / goform / goform_process? GoformId = MODE_SWITCH & switchCmd = FACTORY.
  5. Successful completion of the operation ends with a response (“result”: “FACTORY: ok”).
  6. The Device Manager now contains unrecognized objects. A diagnostic mode driver is required. Install the required software.
  7. Once the devices have been identified, the question marks will disappear. Select ZTE Mobile Broadcast Diagnostic Port. Look at the number among LPT / COM. Find out the exact name, for example, COM9.

We find the firmware image. Open any terminal (including the Windows command line). Copy the image from the directory to the previously defined serial port. For instance:

  • copy / b<имя_образа>\\. \ COM9

Port number selection is illustrated earlier, the name of the image is known including the location. The / b prefix denotes the binary mode of the transfer operation (since the firmware file is in binary format). Reboot your device.

Configuring WiFi ZXV10 H208L and ZTE ZXHN H208N router. Detailed instructions for setting up the "Router" mode and creating a wireless WiFi network.

The ZXV10 H208L (ZTE ZXHN H208N) device simultaneously combines the functions of an ADSL modem, a wifi access point, a SIP telephony client, in addition to a router. The modem has one external port - WAN (Wide Area Network) and four internal - LAN (Local Area Network). WAN is used to connect an internet network cable to the modem. LAN ports provide connection of various devices (PCs, laptops) to the internal network. The modem is configured via the Web interface. To access it, you need a browser such as Google Chrome.


Customization features

We can configure it as follows: in Bridge mode (the Internet will be connected to only one computer), in Router mode, or open ports.

In Router mode, you connect to the Internet directly through your modem. The advantage of the modem in this mode is the ability to simultaneously use the Internet by various devices (tablet, smartphone, PC, etc.). To set up wifi, you must first set up the Router mode.

Setting up wifi on byfly modems, in most cases, is a simple process that does not require special knowledge and skills. Please note that before configuring wifi on byfly modems, you should perform the following operations.

  1. You need to install your modem model (ZXV10 H208L or ZTE ZXHN H208N).
  2. Check if the modem is connected to a personal computer or laptop via a network cable.
  3. Make sure you have a working connection when connecting to the Internet with a network cable.
  4. Set up wifi on byfly modem according to the instructions.

Configuring to Router Mode

The ZXV10 H208L (ZTE ZXHN H208N) device is initially in Bridge mode, that is, there is only one PC access to the Internet; to switch to the Router, you need to follow the instructions below.

Setting up the ZTE ZXHN H208N modem. Setup of the ZTE ZXHN H208N modem

Customization modem ZTE ZXHN H208N's router, customization WiFi, IPTV Setup of the ZTE ZXHN H208N modem in a router, the

Setting up a wi-fi router zte zxhn h108n, internet, wi-fi, interactive TV, multiroom

Detailed description of DSL wi-fi ZTE router zxhn h108n, customization master and manual internet, interactive TV, wi-fi

Launch a browser, preferably Internet Explorer, write down the parameters of the router - 192.168.1.1

Read also


    How to set up a Xiaomi phone: Redmi, Note 4, not others. Only basic options Web, wifi, language not fingerprint sensor. The answer is simple in more than one article ...


    How To Authenticate A Samsung A50 Smartphone Along with the high tech associated with the new Samsung A50 phone model, people tend to think that they can get the same features at a much lower price. Due to the lack of awareness ...


    Sometimes you are very annoyingly calling or sending messages from a subscriber who does not want to hear, in other words, this is just spam and similar unwanted contacts. In order to prevent this, it is enough to block them to get rid of it forever ...

    Dropped an iPhone. The screen does not work If you drop the iPhone, the screen does not work, at first you need to calm down. The consequences of a fall are harsh, but there are effective ways to fix a malfunction in a phone without the help of others ...


    How to install Russian language on HUAWEI smartphone (honor) ?. Most of the world's smartphones are developed and assembled outside of Russia. Therefore, the main language of the smartphone interface is also not Russian. Usually, when you turn on your smartphone for the first time, you will be prompted ...

Open the browser, enter http://192.168.1.1 in the address bar

A new tab will open. Set Username to admin and Password to admin. Click the Login button.

Navigate to the Network Interface / Network menu.


Next, fill in the Connection name, you must select the PVC0 option, and if it is absent –Byfly.


You need to remove the Bridge connection. To do this, click on the "Delete" button.


A new tab will appear. Enter the name of your connection in the New Connection Name field, for example, PVC0. Next, go to the VPI / VCI field, where you should specify 0/33. Enter the information from your contract in the appropriate fields Username and Password, click the "Create" button.


If there is no Internet connection, it is worth checking the correctness of the Username and Password information.

Wi-Fi setup

To configure Wi-Fi on a ZXV10 H208L or ZTE ZXHN H208N device, press and hold the "Wlan" button for about 20 seconds, after which the corresponding indicator should blink. We enter the router settings as indicated above.

Go to the Network Interface tab.


Read also


    How to change SmartHub region for Samsung KPosted 02/08/2017 by by andreyHow to change SmartHub region for Samsung K Preparatory TV setup Change IP address Install (unlock) Samsung smarthub From the off state ...


    This 60+ wifi water leak detector only does the basics but it does them well There was an error emailing this page Sensentric SimpleSENCE Home Leak Freeze detectorWater leak detector when you are valid ...

    How to connect a phone to a computer via usb: Solutions to the problem A very common problem for users who use ...


    Oppo is launching its new smartphone called Oppo A31. This device comes with many new features and modern technologies. 91mobiles recently posted a poster featuring the Oppo A31 designed to triple the rear camera setup ...

Question: How to set up the Internet on smartphones (phones) and ZTE tablets?

Answer: Internet setup on ZTE devices is performed in the following order.

1. We connect the service with the operator. This can usually be done via a USSD request.

To connect to the Internet from Megafon, we recommend following the link - http://www.megafon.ru/internet/, select the type of device for connection, for example - "For a smartphone", select your region, then select a tariff, click "Buy", after then the information will appear, what code must be dialed to activate the service, for example - * 236 * 0 #. We dial this code like a regular phone number.

To connect to the Internet from MTS, we recommend that you follow the link - http://www.mts.ru/mobil_inet_and_tv/, select the type of device for connection, for example - "Internet from the phone", after which a page with the code that you need to dial to connect will open services, for example - * 252 #.

To connect the Internet from Beeline, we recommend following the link - http://beeline.ru/customers/products/mobile/, select the type of device for connection, for example - "On the phone", then select the tariff plan, then click on "Connect" -> "Connection and service management" after which you can see information on how to activate the service, for example, by dialing the code - * 115 * 04 # or by calling the number.

Attention! The page addresses and USSD request codes are for example only and may change over time! To connect, go to the home page of your mobile operator's website and from the home page go to the pages with information about Internet connection. For other operators, the setting will be approximately the same. You can also call your mobile operator on the hotline and activate the service orally. Another option is to come to any operator's sales office in your city, where the sellers are obliged to connect the service to you.

2. To turn on the Internet you need to go to "Settings" -> "Data transfer" and opposite the item "Mobile. traffic "or check the enable checkbox, or move the switch to the right to" On ". For most ZTE smartphones, this is enough to automatically turn on the mobile Internet. After the connection is established, depending on the type of connection, in the notification panel, next to the network signal strength icon, the symbol H (HSDPA), G (GPRS), E (Edge), R (Roaming) or 3G will appear. Also, to check the Internet connection, open a browser and wait for any Internet page to load, for example, by typing “ya.ru” (a light version of Yandex) in the address bar.

Attention! If the ZTE smartphone has a 2-SIM card, then the SIM-card that will be used to access the Internet must be inserted into the WCDMA / GSM slot, and in the settings "Settings" -> "More" -> "Mobile network" -> "Network SIM1 settings ″ (or 2 depending on the model, see the slot number under the cover) -> "Network mode" -> "Preferred network mode" -> "GSM / WCDMA" or only "WCDMA".

3. If the Internet on your ZTE device does not appear after following the previous recommendations, then you need to either get the Internet settings from your cellular operator in automatic mode, or enter the settings manually.

Automatic tuning

If the operator is Megafon, then go to the site - megafon.ru, click on the link "Support" -> "Settings", select "ZTE" there, and then your smartphone model, for example - "V880E" and enter your phone number. After that, the settings should come to your device.

If the operator is MTS, then go to the site mts.ru, then "Mobile Internet and TV" -> "Help and Service" -> "Settings" -> "Phone Settings". There we enter the number and wait for the settings to be received.

If the operator is Beeline, then the automatic setting of the mobile Internet can be ordered free of charge by calling 0880. (The password for saving the settings is 1234.)

Manual setting

If the operator is Megafon, then go to the address http://labs.megafon.ru/dev/, there we select "Other manufacturers" -> "ZTE", we are looking for our device, for example "ZTE Nubia Z5", well, we are trying to set it up like this, as it says.

If the operator is Beeline, then go to the site beeline.ru, there we click on the link "Help and support" -> "Internet settings" in the search field, enter the model of your device, for example - ZTE V790 and then click "Find instructions" and read the information on at the construction site. You can also send instructions directly to your phone by selecting the link "Send SMS with instructions for ZTE V790".

If the operator is MTS, then go to the site mts.ru, then "Mobile Internet and TV" -> "Help and Service" -> "Settings" -> "Phone Settings" -> "Internet" -> "Android", read the instructions ...

General rules for manual configuration

Go to the section "Settings" -> "More" -> "Mobile network". If 2 Sim cards are used, then we select the settings of the Sim card for which the Internet is activated. Next, click on the item "APN Access Points" -> "New Access Point" and enter the settings that are indicated on the website of your cellular operator. After entering the settings, save the access point, reboot the device and rejoice.

In most cases, the following settings are sufficient.