How to strengthen the tricolor satellite signal. Strengthening the satellite antenna signal. Possible home solutions for bad reception because of the weather

1. Inaccurate antenna setup
   Antenna, as you know, should "look" in the direction of the satellite - and to rotate it appropriately, the parameters of the angle of inclination and azimuth are used. The right settings can suggest a special device or a smartphone program, you should not rotate the antenna "on the eye".
   Sometimes it happens that the antenna was originally configured correctly, but she moved a strong gust of the wind or a bird.
   In both cases, to enhance the antenna signal, you need to configure it exactly to the satellite and secure securely. If the problem is repeated - think about purchasing easier aluminum or perforated antenna or on fastening.
2. Obstacle towards satellite
   It happens that the antenna is rotated at the right angle, but is installed in the wrong place. The fact is that there should be no visible obstacles between the satellite and the antenna. Trees, the wall of the neighboring house and similar obstacles interfere with a stable signal reception. Output in this case two: either eliminate the obstacle or choose another place to accommodate the antenna.
3. Little satellite antenna
   If you live in the zone of the sorence of the satellite, then the most correct will connect to another satellite. But sometimes it is simply impossible to do - in some territories there is no high-quality signal from any satellite (for example, some areas of the Far East, the Far North, etc.). In this case, you need to use a "plate" of a large diameter, which will not only strengthen the signal, but also will retain its quality in bad weather.
4. Low converter quality
   Converters supplied in the equipment kit of any operator, usually normal, but not better quality. To enhance the quality of the signal, the converter is better replaced by dear modelor - which is preferable - immediately "collect" a set of equipment independently, under own needs By purchasing and antenna, and the converter.
5. Large number of cable connections
   Each cable connection reduces the signal quality. The rule works here: the less obstacles to the signal path, the better. Therefore, if there is a need to strengthen the antenna signal, you need to eliminate as many of these connections as possible. If a cable splicer was used, replace the cable to whole. If divisters are installed - try using other ways to connect multiple TVs, such as a converter with two outputs.
6. Large low-quality cable length
   With a high length of the cable, the attenuation of the signal is inevitable. But what to do if you need this length? In this case, you need to choose a high-quality cable, with a completely copper, and not compounded steel central residential.

In this article we will talk about how viewing problems may be caused Weak signal.

Raising the signal level, you clearly do not achieve what the number of channels will increase. The exception is the case if several transceivers are used.

What to do when the picture is scattered into squares or disappears at all?

In a word - the equipment does not receive a signal from the satellite. This may occur for various reasons, but the problems are easily eliminated. Perhaps the antenna turned under the influence of the wind or someone turned her - for a poor-quality signal, it is enough for it to move at least a couple of millimeters. It is likely that errors were made initially when setting up the plate, and the disappearance of the signal is associated with a large cloudiness or rain.

Why does an antenna change its position?

Typically, the fastening bolts are normal. Accordingly, to increase the signal, you need to correct the direction of the antenna and fasten the fastener (it is necessary to adjust the converter.

If there were no problems with the quality of reception quality, and now it began to fade, especially in the summer, then the reason to the banal is simple. On a tree, located next to the house, in the direction of the antenna, a new branch has grown - it becomes an obstacle to the signal path. It will be necessary to get rid of the branch or wood at all, or find another place for the plate.

Wires and other technical problems with a weak signal

Also, the disappearance of the signal may be associated with a wiring of poor quality: due to damage to the insulating layer of moisture, it seeps into the cable or it is simply overlayed. It will be necessary to replace the wire, but it is not necessary to save on quality. When laying the cable, it is necessary to reliably fix it, which will exclude a breaking when the wind gusts.

If a long cable is laid, the signal attenuation can occur. Accordingly, problems arise with the reception of the channels: the signal is good only near the plate, and he simply does not reach the apartment. Eliminate the problem will help the signal amplifier, which is installed between the antenna and the receiver.

It happens that the receiver itself comes out of order (very rarely). Then without the help of a specialist just can not do. You can check the help of the receiver by diagnosing it: disconnect and connect the wire to the receiver (it is important that the rest of the equipment is regular) - from the signal side of the signal there should be some kind of reaction. When the power supply breaks, problems arise with the inclusion of the tuner. However, this can also make a signal to disappear.

If nothing is observed, and the signal is still not enough, then it is possible to increase the reception by increasing the diameter of the plates mirror. At the same time, the optimal size of the antenna is selected taking into account the locality where it will be installed.

The cable and broadcast television broadcast systems are developing everywhere everywhere. However, despite the rapid growth of the network and extended television capabilities, the image quality on the TV screen is low. This is explained by the fact that the reception of the antenna TV signal depends on various factors: proper Installation, Designs and forms of the device, distance to the repeater. Improve the quality of the resulting image will help autonomous amplifying device Or replacing the receiver to a more powerful apparatus. In this review, we consider how to strengthen the weak unstable TV antenna signal.

Before learning radiotechnical new items, it is necessary to analyze why the level of functioning of the receiver is low. The causes of interference and poor image quality can be:

• significant removal of dwellings from the repeater;
• wrong;
• high level natural noise;
• external obstacles to signal reception: high-altitude homes, trees, industrial structures;
• cable failure;
• incorrect orientation of the transmitter;
• the presence of metal objects near the antenna capable of carrying out electricity;
• outdated technique.

Ways to enhance the power of Teleantenna

1. Change the location of the antenna. As a rule, it is directed to the side transmitting tower.
2. Acquisition antenna amplifier. They are electrical devices that are connected directly to the antenna and give an impetus to improving the received signal.
3. Expand the number of antennas for a clearer image installed at the highest place.
4. Change the device to a more powerful TV antenna.
5. Remove all objects and metal subjectswhich may interfere with the adoption of a TV signal.
6. Check television cable For integrity. In case of closures or breaks, change it to a new one. For high-quality signal, it is important.
7. Create effect syphase antenna lattice (SAR). It is that identical receivers constitute a complex system that works on the overall consistent load so that the signal phases are the same.

Knowing how to improve television signal, You can minimize the interference of the image on the screen and enjoy high-quality viewing, regardless of the distance to the television center.

Antenna amplifier

Advantages and disadvantages of antenna amplifiers

Like all radiotechnical devices, the devices have their advantages and minuses. The advantages of antennas amplifiers include:

• due to the operation of the device, even a weak television signal is accepted;
• minimal noise coefficient;
• improved signal in a wide frequency band of several wave ranges.

The main disadvantages that users may encounter:

• overloading the apparatus from powerful signals in the meter range of MV (49-230 MHz);
• self-excitation amplifier;
• device susceptible to currents of thunderstorm electrical discharges;
• passive losses arise at the exit.

How to choose an antenna amplifier

In modern amplifiers mass technical parametersshown in the documentation for the device. The trouble is that the user often does not have a sufficient level of knowledge to appreciate them correctly. Therefore, choosing the device stands on a number of the most important characteristics.

1. Recommended reception range. It can be from 30 to 150 km. Describes the distance between the antenna and the broadcast station, in which the amplifier will show good results.
2. frequency range. There are broadband amplifiers working with all broadcast standards. You can buy a device only for CETTV or capable of taking short waves.
3. Gain. It is incorrect to consider that the more this figure, the better. The optimal value is at 27 dB. Such a device is suitable for receiving up to 50 km. More serious models with ku about 40 dB will provide good signal in difficult conditions. But if you put a very powerful amplifier on the antenna, it can trigger the protection of the TV or console, blocking the signal.
4. Supply system. Models are offered for direct inclusion in a 220V socket, with a power supply or 12V input, 5B. There are products that work only with consoles or TV with power cable.
5. Type of housing and execution. Amplifier can be designed to install on an antenna in street conditions, to have protection against water and dust. Or execute in the case for premises, designed for accommodation only near the TV.

The optimal solution for the CETTV will be an amplifier with power cable. Today, such an option on the connection port offers a huge number of consoles.

Tip! If old equipment is used, it is recommended to buy an amplifier with its own 5V power adapter.

Top amplifiers

The ranking of the best includes devices with different applications, type of execution and a regular installation site. They do not require a challenging setup and show good results of use in a huge amount of cases. Some models allow you to accurately rebuild the characteristics of the signal to get the optimal picture quality at all without exception to the received channels.

SWA 9001/999/9999/9009/9701 (L) broadband

Cheap and angry - this is how this amplifier can be described. He has no adjustments. The device is enough to connect to the antenna, it gets the power cable. Amplifier broadband. It can be installed on both indoor and outdoor antennas. In the latter case, protection is necessary for the case of precipitation. The device provides a reception range up to 90-110 km, suitable for the CETTV signal.

• price tag;
• versatility of use;
• reception distance;
• easy installation.

• offered without a protective housing;
• has an uneven gain coefficient within the frequency range;
• there are no adjustment methods.

• price tag;
• suitable for CETTV;
• ease of installation;
• LN (Low Noise) low level noise.

• no settings;
• average gain coefficient;
• different ku in separate frequency bandwidth;
• only for power consoles on the port.

This amplifier is very popular. It is simple and at the same time offers a good level of characteristics. And most importantly - safety use. Installed indoors, it does not require special ventilation conditions. The device consumes only 7 W, has two outputs, provides a coefficient of amplification of decimeter waves in 24 dB. The device is suitable for receiving the TTV signal. It is completely self-sufficient, turns on directly to the 220V network.

• simplicity;
• safety;
• good coefficient of strengthening of the CETTV;
• two outputs.

• only for installation indoors;
• requires a 220V socket;
• power connection cable is short enough.

This amplifier is able to save its owner from any problems with tv taking to an external antenna. The device refers to the mast type and designed for installation on the street and work in the most difficult conditions. It is made in a fully sealed metal case. Included the supply of your own 24V power supply unit. The gain is adjustable, from 15 to 35 dB, you can adjust the equipment in accordance with the reception area. The amplifier is connected by F-connector, it has one input and two outputs.

• secure execution;
• full set;
• adjusting gain;
• suitable for CETTV.

• only for working with CETTV;
• requires a 220V socket;
• two functional blocks.

Positionable as a house, this amplifier will an excellent solution for private housing with large number TVs. Or for an apartment where the reception of the CETTV is made on the outer antenna. The device generates a high level of signal, has a gain of up to 20 dB, capable of adjusting the inclination of the frequency response to setting optimal quality on all channels. The rate of non-uniformity ACH is only 0.5 dB. The amplifier can operate at temperatures from -20 to 50 degrees, but must be installed indoors. Him low noise coefficient.

• high output level, suitable for network from several TVs;
• broadband, from 47 to 862 MHz;
• suitable for CETTV;
• allows you to carry out a thin setting;
• there is a test port to configure antenna.

• average basic ku;
• price tag;
• only one way out;
• to connect, you need a 220V socket.

Antenna amplifier do it yourself

You can construct a simple device that enhances your TV signal for the TV with your own hands. Such an adaptation has low power consumption, does not create significant interference, and has a frequency range of up to 900 MHz. The low-voltage amplifier with a power of 2.7-5.5 V consumes current of 3 mA, it works very quietly.

Various factors can negatively affect the level of television signal. Modern radio technological devices help to increase it. They have a number of advantages: mobility, high gain and large selection of models. Thanks to the collaboration of the antenna and the amplifier, you can watch television in good quality.

Top TVs 2018 according to buyers

TV LG 43UJ634V.

TV SAMSUNG UE50MU6100U.

TV HYUNDAI H-LED24F402BS2

TV LG 22LH450V.

TV SAMSUNG UE22H5600.

Some of the large number of satellite TV subscribers are faced with a problem - a signal received by a satellite antenna, insufficiently strong and with a deterioration of weather conditions, the picture of the received channel is scattered and disappears.
When viewing a favorite transfer or a movie, such "scatters" are starting to annoy and here at this stage and the idea that it is necessary to increase the signal received by the satellite antenna in any way.
When the task of a better satellite receipt is solved, it is necessary to diagnose the equipment for receiving the signal and deal with the causes of not sustainable reception of the signal from the satellite and these reasons are eliminated.

Causes of weak satellite reception

In fact, such reasons are not so much - they can be determined and eliminated. Sometimes it is enough to eliminate only one of several reasons in order to significantly increase the quality of the received satellite signal. So, the causes of weak signal reception:

	Insufficient satellite antenna size The larger the area of \u200b\u200bthe host antenna, the higher the quality of the received signal. There is a concept as recommended size satellite antenna. For receiving TV channels different operators Communication recommended antenna size is different. For example, for the territory of the Krasnodar Territory, the recommended antenna size for Tricolor TV reception is 55-60 cm, for receiving continent, Telekart, Rainbow TV - 90-100 cm, for TURKSAT reception, HotBird - 90-120 cm. It is clear that the larger size The antenna that it is more expensive both by itself and in the installation. But the large diameter pays off a stable picture on the TV with the deterioration of weather conditions. So, if the signal from the satellite antenna is weak, then it is possible to install a larger diameter antenna. For example, an antenna replacement with 55 centimeters by 60 centimeter for receiving a tricolor TV allows you to increase the signal from the transponder 12190 MHz / 27500Kbps from 75 to 95 on the taking equipment scale
Outdated converter model The converter is an important link at the stage of receiving satellite broadcasting. The high-quality converter provides an excellent reception over the entire range of received frequencies and gives a good signal supply with a worsening of the reception conditions. It often happens that the satellite equipment set is installed using an inexpensive converter, which was included with the equipment. Often such complete converters initially low quality and supply them to reduce the total cost of a set of satellite equipment. Such "initial" converters usually change by us on Galaxy Innovations converters, which have excellent TTX. So replacement of the regular "gray" converter on an antenna 55 cm on the GI 121 converter allows you to increase the received signal from 75 to 85 on the scale of the receiving equipment on the transponder 12190 MHz-27500Kbps.
	Poor quality / shot satellite antenna Not always an antenna is configured to receive a signal with the use of technologies - special instrument, simply speaking. According to the signal scales on the TV, it seems that the antenna is completely configured. But only on the instrument of the antenna can be set as much as possible - along the angle of inclination and azimuth. It also happens that the normally tuned antenna shifts from the direction of a strong impact of wind or a strong mechanical effect. Most often from the direction knocks out the antenna 55-ku, because It is attached to the support of only one clamp, in contrast. For example, from 60-ki which is equipped with 2 clamps and is shown in the image on the left. Whatever the reason for the incorrect antenna setting - it is important to re-put its true direction to the satellite and securely fix on the support. Using a large number of companions along the cable It happens that it is not enough of almost enough of the cable installers to connect an antenna at the facility. What to do in such a situation? In such a situation, cable passages are often used. And sometimes not one such a sparer. Using a 3-EX of pigliers along the cable reduces the signal from 90-95 to 70-75 points - And even below, it all depends on what the cable brand is used. In the event that there are many connections on the cable to completely replace it with a solid piece of cable.
Large low-quality cable length If a high-quality cable with copper central residential cable is used, then even on large lengths of the cable used, there is no significant attenuation of the signal, as in the cable with the overed steel central residential. If a large-length cable is used with steel central residential, then replacing it on a high-quality cable with copper Czem will reduce signal loss during transmission. The use of circuit outlets and other signal suppressors It is necessary to analyze the entire path of the cable from the antenna to the receiving receiver and eliminate all sorts of connections, dividers, circuit outlets And other extenders of the signal. There is a simple rule - the fewer obstacles along the signal path, the fact that it is higher. In the perfect case, the cable must approach the release of the converter directly to the receiver - without any obstacles.
	Appearance of obstacles in the direction of satellite After installing the satellite antenna opposite her can be built house or can grow a treeIt happens that the antenna in the winter is installed opposite the tree, and the leaves are blocked in the spring and they completely block the reception of the satellite signal. In the event that an obstacle appeared before the antenna, there are 2 ways to solve the problem - reinstall the antenna or eliminate the obstacle.

Having considered all the listed causes of the weak signal from the satellite antenna, it is possible to conclude that it is possible to take the following to enhance the signal from the antenna - to increase the antenna size, replace the converter to high-quality, carry out the exact setting of the antenna to the satellite, pave a new high-quality decrease cable without compounds, eliminate Interference before the antenna towards the satellite, remove various dividers-repeaters-circuit sockets.
In the event that you intend instruct work to strengthen the received satellite signal to specialistsYou can contact our company.

This is essentially a very important subject in successful watching TV.

After all, it will depend on the correct installation of the antenna, it will catch a signal from the satellite or not.

Understand yourself if not ... then the picture will not.

The position of the satellite antenna horizontally.

That is, the azimuthal direction of the antenna mirrors, from your location point, which you will define according to the compass ( Fig. one).

Bad weather may affect the reception of the signal even correctly connected and the directional system. If you live in the country's region, which receives heavy annual showers, you probably encountered this problem several times. Snow and ice, which accumulate on the dish, can also affect the reception, as well as strong wind.

How rain affects satellite signals

During the shower, rain drops can weaken or absorb the signal on the way to the satellite antenna. The rain can also cause signal scattering, since the electromagnetic waves refract and difflect around the raindrops on the surface of the plate. Mini-dishes are better designed to minimize the loss of the signal due to weather, but large dishes are better in areas with frequent strong rains, since they better compensate for the reduction in signal power due to weather.

For horizontal setting, we will move the mirror itself (reflector), on EAST (E. - EAST), or on WEST (W. - West).

Really etot, the process must be combined with a vertical setting ... I will immediately say that it has a smysl to call for a specialist operation.

At least to configure the plate to be problematic.

Possible home solutions for bad reception because of the weather

Nevertheless, the rain is the only criminal. Snow, ice, strong wind and strong fog can affect the satellite signal. Most satellite receivers have built-in error correction to try to correct the intermittent signal. If your dish is located under trees or eaves, where water falling from the trees or the roof is landed on the dish, move the dish into the dry area. If the dish is installed on the side of the house, you can set a transparent piece of fiberglass in front of the dish. Fiberglass acts as a screen for a dish, so water does not affect the ability of the dish to receive a signal. This prevents the rain sticking to the dish, which can lead to its improper transmission of signals. Depending on how often it rains in your area, you will need to spray the dish at least once every three months. If the rain is accompanied by strong winds, the dish may not coincide with the satellite. It is likely to happen when the dish is mounted on a high pole. Although you may, and you can make rearrangement yourself, you may be better to call a professional for this task.

Work with snow and ice

Spray your satellite plate with a non-stick spray. . Heavy snow can affect the quality of the signal, but it is less affected than heavy rain.

Positioning the satellite antenna horizontally.

The second parameter is the position of the satellite antenna, vertical.

That is, the angle of her tilt ....

The antenna angle (Fig. 2) will directly depend on what height is the satellite itself, and therefore the angle of lifting on the satellite or how else it is called an angle of space.

The accumulation of snow and ice on the dish affects the reception of the signal, so the subscribers who live in the cold parts of the country, sometimes buy dishes with embedded heaters. The accumulation of snow or ice on the dish can prevent the signal or withdraw the dish from the satellite position, which affects the signal.

In addition to positioning a plate, where the cluster of ice and snow is less likely - not under the trees or eaves, where there is a stock - little that can make a homeowner to prevent interference. Make sure the cables are not disconnected or disconnected in the rear of the box.

Well, if you think about yourself without special equipment then approximately so ...

Let's start with the central head that should be configured in our Sirius. In the receiver set the frequency 11766, the speed 27500, the polarization "H".

On the receiver you have two stripes:

Check the input connection

You can also make sure there are no objects that may be accidentally placed on the cable. If all cables are good, try to do the following. The light will change to yellow, showing that the digital window is in standby mode. This step will interrupt any records that are currently in the process. However, saved settings and recorded programs are safe.

Unscrew the cables for feeding dishes and check two things. Call the engineer if the cables are removed from the metal housing or nozzle bent or broken.

• Two separate parts of the cable should not touch each other.
• Always keep the kernel and weaving separately.

If the cables are in order, carefully insert them back to the socket and tighten the screws.

One Meaning Plate Connection and Satellite Signal.
The second shows the level of this signal.

When the satellite antenna is connected correctly, you must see the signal level of approximately 40%. It remains to configure the quality of the signal that we have on zero.

Go to a plate and let's start ...

Antenna turn to the left and up to the stop and in search of best level Signals slowly turn on left to right until it stops.
If the signal is not found, we lower the plate for 2-3 mm on fastening (on the fasteners of the plate to the bracket, there are marks with numbers for a more convenient "shot"), and turn to the right left until it stops, then omit even lower and so that the signal does not appear.

You will receive signals test menus. The signal must be at least 50% if the weather is good and about 40%, if the weather is bad. If you do not have a signal power, try the following steps. If you receive a message in which it says: "There is no satellite signal" - error 25 or error 29, you can try to reset your digital block. Wait about half a minute and connect all the items that you have turned off and turn on the network. Check if you have a signal.

Easy so that the dish is knocked out from under aligning with something from the weather so that someone put the stairs to clean the high windows or check the groove. If the dish was knocked out of the position, you can try to rebuild it yourself or call the technique to do this for you.

When you catch a signal, you will see how the indication band appears. If you approached the satellite approximately, the signal quality band will be about 21% - fasten the antenna in this position.

Now we lower a little and carefully turn to the left, we look at changes in quality, if it decreased, then we return the antenna to the original position.

While you are there, you can also check out the overall condition of your dish. It can be strongly rusty or corroded, and in this case a replacement is necessary. There are times when this is a good message. This is what we call the "signal loss". It does not happen often or long. Read on to learn about the reasons for the loss of the signal and what you can do to minimize it. How can you say that you lost your signal? This means that you get a satellite signal from your dish.

If it is red, it means that the receiver does not receive any information from the plate. You can check the actual signal strength in the "Parameters" menu. Go to "Changing System Settings". You will see a histogram from 0 to 99, showing how strong the signal. In the field next to the schedule there is a room. You will notice that it fluctuates in four or five points in any direction. This is normal and is the result of atmospheric conditions.

You caught a signal by 40%, but this is still not enough, with so much percent the slightest wind or the rain can break your viewing of the telecast.

To increase the quality of the signal, turn the converter first by, and then counterclockwise and look at what position the signal quality will increase.

If the mount allows, the MirSovets advises to try closer the converter to the mirror, and then remove.

More than 80 means you get the strongest signal. Perhaps this is a clear, calm day. Typically, the signal level will be in the range from 70, and if you are at the bottom end of the range, moderate weather conditions can affect the signal, such as clouds, rain or snow. However, you still have to see a clear image. This means that you are experiencing some interference of the signal. On the way to the satellite can be a strong storm.

If the reading of the signal strength is constantly below 60 and, as it seems, does not change under weather conditions, the dish can lose alignment. The unequivocal number often means that the problem is related to the connection between the receiver and the dish. Even without a signal from the satellite, the dish will have a rating of about 20.

This also affects the signal quality, but usually the length of the bracket for the central converter is always adjusted along the length. Normal signal quality is 65-70%.

However, ... as already wrote with a handy specialist.

Special attention should be paid to the device to configure SF-500 satellite antennas.

The device has a memory in which all the main satellites used in our regions may be edited by the buttons on the instrument panel.

Satellite signals are not protected from degradation. They cannot pass through solid objects, so you can sometimes encounter the signal interference in rainy weather. Thick clouds, hail and snow can block your signal. The storm also should not be right behind your door to influence your signal. Signals move thousands of kilometers from satellites, located high above the equator along the longitudinal line, up to the middle of the Texas or North Dakota. The path can temporarily disrupt the service.

Often you lose your signal when the assault goes, and then return the signal when it is poured on your roof. The signal path does not go straight upwards, and at an angle to the south. The signal path can pass directly through the center of the storm. The good news is that weather interference is almost always short-lived.

In a word ... an excellent assistant when tuning the satellite antennas. Specifically about the device.

Good luck, friends!

Some of the large number of satellite TV subscribers are faced with a problem - a signal received by a satellite antenna, insufficiently strong and with a deterioration of weather conditions, the picture of the received channel is scattered and disappears.
When viewing a favorite transfer or a movie, such "scatters" are starting to annoy and here at this stage and the idea that it is necessary to increase the signal received by the satellite antenna in any way.
When the task of a better satellite receipt is solved, it is necessary to diagnose the equipment for receiving the signal and deal with the causes of not sustainable reception of the signal from the satellite and these reasons are eliminated.

It must have a clear idea of \u200b\u200bsatellites for good signal reception. So, if the high level rises to the south of your home, you can lose your signal. He can also do the same. Some people set their dish in winter and get signals very well. Then, in the spring, when the leaves come out, they lose the signal. Either pull out the ax, or call our installers so that they are positioned again!

He enhances them and sends them to the recipient. Easy coating or very dry, peeling snow usually do not cause signal loss. Wet, heavy or deep snow will. If your dish was correctly installed, it should not collect a lot of snow. A good wet snow dump can lead to a signal loss. If this happens, and if the dish can easily and safely get, carefully clean the snow with a broom.

Causes of weak satellite reception

In fact, such reasons are not so much - they can be determined and eliminated. Sometimes it is enough to eliminate only one of several reasons in order to significantly increase the quality of the received satellite signal. So, the causes of weak signal reception:

	Insufficient satellite antenna size The larger the area of \u200b\u200bthe host antenna, the higher the quality of the received signal. There is such a concept as the recommended satellite antenna size. For receiving TV channels of different communication operators, the recommended antenna size is different. For example, for the territory of the Krasnodar Territory, the recommended antenna size for Tricolor TV reception is 55-60 cm, for receiving continent, Telekart, Rainbow TV - 90-100 cm, for TURKSAT reception, HotBird - 90-120 cm. It is clear that the larger size The antenna that it is more expensive both by itself and in the installation. But the large diameter pays off a stable picture on the TV with the deterioration of weather conditions. So, if the signal from the satellite antenna is weak, then it is possible to install a larger diameter antenna. For example, an antenna replacement with 55 centimeters by 60 centimeter for receiving a tricolor TV allows you to increase the signal from the transponder 12190 MHz / 27500Kbps from 75 to 95 on the taking equipment scale
Outdated converter model The converter is an important link at the stage of receiving satellite broadcasting. The high-quality converter provides an excellent reception over the entire range of received frequencies and gives a good signal supply with a worsening of the reception conditions. It often happens that the satellite equipment set is installed using an inexpensive converter, which was included with the equipment. Often such complete converters initially low quality and supply them to reduce the total cost of a set of satellite equipment. Such "initial" converters usually change by us on Galaxy Innovations converters, which have excellent TTX. So replacement of the regular "gray" converter on an antenna 55 cm on the GI 121 converter allows you to increase the received signal from 75 to 85 on the scale of the receiving equipment on the transponder 12190 MHz-27500Kbps.
	Poor quality / shot satellite antenna Not always an antenna is configured to receive a signal with the use of technologies - special instrument, simply speaking. According to the signal scales on the TV, it seems that the antenna is completely configured. But only on the instrument of the antenna can be set as much as possible - along the angle of inclination and azimuth. It also happens that the normally tuned antenna shifts from the direction of a strong impact of wind or a strong mechanical effect. Most often from the direction knocks out the antenna 55-ku, because It is attached to the support of only one clamp, in contrast. For example, from 60-ki which is equipped with 2 clamps and is shown in the image on the left. Whatever the reason for the incorrect antenna setting - it is important to re-put its true direction to the satellite and securely fix on the support. Using a large number of companions along the cable It happens that it is not enough of almost enough of the cable installers to connect an antenna at the facility. What to do in such a situation? In such a situation, cable passages are often used. And sometimes not one such a sparer. Using a 3-EX of pigliers along the cable reduces the signal from 90-95 to 70-75 points - And even below, it all depends on what the cable brand is used. In the event that there are many connections on the cable to completely replace it with a solid piece of cable.
Large low-quality cable length If a high-quality cable with copper central residential cable is used, then even on large lengths of the cable used, there is no significant attenuation of the signal, as in the cable with the overed steel central residential. If a large-length cable is used with steel central residential, then replacing it on a high-quality cable with copper Czem will reduce signal loss during transmission. The use of circuit outlets and other signal suppressors It is necessary to analyze the entire path of the cable from the antenna to the receiving receiver and eliminate all sorts of connections, dividers, circuit outlets And other extenders of the signal. There is a simple rule - the fewer obstacles along the signal path, the fact that it is higher. In the perfect case, the cable must approach the release of the converter directly to the receiver - without any obstacles.
	Appearance of obstacles in the direction of satellite After installing the satellite antenna opposite her can be built house or can grow a treeIt happens that the antenna in the winter is installed opposite the tree, and the leaves are blocked in the spring and they completely block the reception of the satellite signal. In the event that an obstacle appeared before the antenna, there are 2 ways to solve the problem - reinstall the antenna or eliminate the obstacle.