The latest version of the GS 8306 receiver update. Tricolor TV - update of the receiver software. Receiver firmware via USB service port

On the company's website of the manufacturer of equipment for the tricolor appeared new software For the receiver GS 8306 is the firmware version 1.9.160.

This firmware was called upon to replace the version of 1.2.001, released several years ago. It must be said that the firmware version 1.2.001 for GS 8306 is exactly the software with which the GS 8306 receiver began to work more or less normally and steadily - it did not hang, the picture practically did not catch the frieze, the channels switched pretty quickly. With the firmware 1.2.001, the receiver GS 8306 remained not cured by only one sore - could fail the external power supply unit 12V, 2A, but the problem was solved by buying another block at a price of 500-700 rubles. Yes, even the above problem is not very common at the GS 8306 model.

And after several years of successful operation of the receiver with a verified and proven firmware for some reason it took a new software version 1.9.160.

Well, they released a new firmware and released. Usually, after updating the software receivers, the tricolor begin to work more stable. There was a calculation on the fact that after the firmware to 1.9.160 everything will be fine.

The site manufacturer's website GS 8306 shows the following characteristics new firmware (See Screenshot below):

Changes compared to previous version software:

  1. Modern graphic interface By stingray
  2. Increased the stability of the receiver
  3. Added functionality manual search Channels
  4. Improved application "Cinema Tricolor TV"

Description of characteristics new version ON receiver GS 8306 - version 1.9.160 picture - page screenshot at the address - http://gs.ru/support/manuals-and-software/gs-8306/

I would like to pay special attention to clause number 2 of the description of the new firmware - increased the stability of the receiver !!!

We in practice faced the following problems when flashing and flashing the GS 8306 receiver to version 1.9.160
  1. the receiver is sewn through the air and if you confirm the execution of the firmware, it may not be crowned with success - the firmware process freezes and the receiver remains in the non-recriminated state. At the same time, the old firmware is already Star. So The receiver turns into a brick. Its restoration is possible only by falling out the Flash memory chip, flashing it in the programmer and reverse sealing to the receiver. This is a relatively expensive procedure.
  2. Another problem when flashing is a large duration of its execution. People begin to be confused on whether the firmware has already ended or the procedure still continues. When confusing and not withstanding, many of them from impatience turn off the receiver from the power supply network and if the firmware has not yet completed, then the receiver again turns into a brick.

Those subscribers who are lucky and whose receiver after a few hours still successfully updated to 1.9.160 will have to face other problems in the receiver to that worked stable.

  1. Periodically, the message "No signal" appears when viewing the channels. After such a message, you can switch to another channel, to see it a bit, return to that channel on which the message "No signal" appears and continue to look at the selected channel again. But only until the next message appears "No Signal".
  2. From the description of the new firmware it is clear that it received the "time-based graphical interface by Stingray". So the needs of this very stingray exceed on our subjective sensations of the processor and the memory of the GS 8306 receiver. This leads to the fact that the channels now switch much longer than before - not the old firmware 1.2.001.
  3. When switching channels, especially when switching channels of different thematic packets, some receivers are simply rebooted.
  4. Pink shade image after turning on the receiver. Some users really encountered the problem of the fact that after the firmware all their channels are shown in pink. Although, maybe it is good - look at the picture in pink in our 21st century. The problem is eliminated by the reservoir overload.
  5. It may be terribly a picture on some channels. On our test receiver, the channel "Match HD" is particularly introduced - number 103 in the channel list.
  6. If, after the firmware, the receiver did not turn into a brick and continues to function badly, then sew it through a USB port back to the stable firmware 1.2.001 will not work - it is worth blocking
  7. Periodically, the receiver restarts by itself even without any actions, such as channel switching
  8. Periodically, the sound and theronization of sound and video tracks
  9. Periodically, the receiver simply hangs, especially when it is experiencing some kind of load, for example, when switching channels.

This is perhaps the main points with which the GS 8306 receiver holders will encounter on the new firmware 1.9.160. And in our, again, subjectively, most of the listed problems are related to the fact that the GS 8306 receiver hardware power is not enough to satisfy all the needs of the new in Stingray.

In the light of all identified problems of operation with a new firmware 1.9.160, it remains only to guess what increasing the stability of the receiver is the developer of the software.

Now about how to continue the operation of the receiver on the firmware 1.9.160

This is what we have done personally with our own GS 8306 receiver to increase the stability of his work. This is the method that the colleagues faced and dealt with the problems of firmware 1.9.160 before us - to increase the stability of the receiver with the received signal, the frequency (lower and upper) heteroodine is needed to set 1 MHz above the standard value - 10751 MHz against standard 10750 MHz.

After the income frequency of 10751 MHz was set, the receiver stopped to give out the message "no signal" when viewing the channels and began to work when viewing and switching the channels more stable. Make anything more difficult.

What else needs to know when operating GS 8306 on the firmware 1.9.160

The new firmware changed the mode of operation of the receiver. Now the receiver automatically determines which video output is connected to the TV connection cable. Depending on which video output firmware will detect the connection cable to the video output, it is video signal and will apply. In the case when 2 cables (HDMI and 3RCA) are connected to the receiver (HDMI and 3RCA), confusion may occur and the receiver does not understand what video output video output. Therefore, at one point in time, only one video cable is connected to the receiver.

Another point is the light indication on the receiver. If earlier the upper burning indicator meant activity HDMI outputand consoles, then on the firmware 1.9.160 glow only the top indicator means that the receiver is in standby mode and to start viewing it is necessary for starting to turn on. And after turning on the receiver automatically serves a video signal to the discovered video output.

Download firmware 1.9.160 for GS 8306

If it is very necessary, then the "omnissal" firmware for the receiver GS 8306 can be downloaded on the official website of the manufacturer of this receiver at http://gs.ru/support/manuals-and-software/gs-8306/

P.S. - After lengthy problems with the development of a new firmware for the receiver 8306, a number of questions arose:

  1. why was there a new software for the receiver if the old worked stably and almost no complaints
  2. when a new software manifests itself, which fixes all problems and errors in version 1.9.160

Digital Satellite HD Receiver

IMPORTANT!!! The stingray firmware for this receivers model with a weak processor is very unstable - possible problems:

  • loss of pictures and sound
  • flicker during the inclusion of electric conbrons and light
  • hanging and slow channel switches
  • spontaneous reset to factory settings when power outages
  • the disappearance of the signal from the antenna

Return the previous version of the USB version will be impossible.PS (only falling out the flash memory and its flashing in the programmer)

Before upgrading, read the instruction in the archive.

Unofficial on:

Compared to previous software versions:

  • Upgraded operator selection menu.
  • Implemented a new status menu interface that simplifies the menu data.
  • Improved the overall operation of the receiver.
  • An information block appeared, which contains a description of the main methods of payment for the Tricolor TV services.

On the comments of the user Vale9041 from the forum http://www.telesputnik.ru

There was an opportunity to remember the receiver settings through the standby mode, even if it was disconnected from the power supply.

Procedure Next:

If you have just created the favorites and turned off the receiver with a cord from the power supply, then re-turned on, the receiver will switch to Tricolor Channel, return button With two circular arrows (the so-called Last) we will find yourself on the first channel created in the favorite.

If we, when viewing a favorite, we translate the receiver from the remote to the standby mode, then turn on again, in the following when the resa is turned off the cord and turn on it back, the return button will return it to the favorites of that channel in which you transferred it to the standby mode from the console. That is, the standby mode serves as memorization.

You can also do the same with the volume ... If you set the volume to the maximum, and resize to the standby mode, then the maximum volume will stand at the subsequent inclusions. But this, provided that if you later disconnect the res cord from the outlet.

you can also do whatever the receiver remembers the general list of channels in one column or width in three columns (view)... that is, the duty regime is a memorization of what we want ...

Past releases

Compared with the previous version of the GS8306 receiver software GS8305.The following changes are made to version 1.0.49:

  • Improved algorithm automatic search Channels "Tricolor TV".
  • Removed the ability to delete a list of television channels and radio channels generated by default in all TV lists and "All Radio".
  • When primary configuration, a channel is displayed under the number "0".
  • Removed indication of pressing buttons in STANDBY mode.
  • When you first switch to the list of radio channels, the receiver is included on the radio channel number "0".
  • Optimized work EPG
  • Implemented work with right polarization.
  • Service TV Mail. The Delete Mail button is renamed to "Delete a letter".
  • List of channels. The functional button "Width" is renamed to "View".
  • Fixed incorrect inscription in HDMI mode "Time-Out of Volume Scale. In version 1.0.049, the inscription has the form: "Volume scalation time.
  • The confirmation dialog boxes are implemented to the left for the right ("Yes" - "No", the default cursor to "no").
  • Improved service "Cinema Tricolor TV" service
  • Improved receiver compatibility with TVs when connecting to HDMI interface

Receiver firmware via USB service port

GS-8306 has no RS-232 port (COM), but has a USB service, it is stitched through it. For the firmware we need usual USB flash drive, I. latest version File firmware for the receiver GS-8306 you can downloadabove .

Check which version on the receiver is installed you can in the main menu

DRE info> Satatus


Firmware order:

1. File SSU_GSC_STB.UPG.copy by USB Flash.without renaming.

2. Insert USB Flash to the receiver and restart the power receiver, do it can be pressed the button. "Stand By"on the front panel of the receiver. Once the power turns on, the firmware process will begin, this will indicate the corresponding message on the TV screen.

Now it remains only to wait for the end of the process. When the firmware is over, a successful firmware will appear on the TV screen.


3. After the allowing message to extract the USB Flash on the TV screen, extract USB Flash.

IMPORTANT! Removing USB Flash before the corresponding allowable message appears on the TV screen is not recommended, otherwise the receiver fails.

Rollback on early version It is not possible, in the receiver can be replaced by either on the current version or more new.

If the firmware does not go, then:

Format a USB flash drive in FAT or FAT32 any utility, such as HP for flash drives, but not in Windows, type click right-click Mice on the flash drive and the format may not help.

We throw the file on the USB flash drive.

We insert into the receiver enabled, we wait a minute you can and turn off the button on the device, you can immediately turn on the same button.

Seconds after 10, maximum 30, the inscription will appear that there is a firmware.

If the inscription did not appear and begins to flax, the waiting mode indicator means that the firmware has not begun.

Update on GS 8305 and GS 8306 models across satellite

On March 11, 2013, the EutelSatW4 / W7 satellites (36A / 36B) will be launched software update (software) for receivers GS8305 and GS8306 models, aimed at improving and improving this receiving equipment. Subscribers "Tricolor TV" will be able to update the receiver at any time in the period from March 11 to April 8, 2013.

Before starting the update, write down the current version of the software, going to "Menu" -\u003e « DRE info "-\u003e" Status ". At the end of the update, the receiver version must change to 1.1.001 . New software will be loaded from the ether.

ATTENTION! In no case are not turned off the power receiver until the update procedure is completed! Otherwise, a receiver is out of order possible!

To update the receiver, follow these steps:

1. Remove the power cord of the receiver from the outlet, and then turn on the receiver again to the network.

2. Switch the receiver on the TV channel "Infocanal" Tricolor TV ".

3. After a few seconds, a message appears on the screen about the need to update the following type receiver:

When appearance this message Select the "Yes" option, click "OK" on the remote control.

Attention! If there is no message about the need to update the software for 5 minutes on the TV screen, you need to reset the receiver installation to the factory ("Menu" - "Settings" - "Factory Settings" - "OK").

4. After the consent to the update, the service messages about the receiver update process will be displayed. The message view is listed below. Update software takes about five minutes.

Attention! During the software update, it is forbidden to turn off the power of the receiver! Otherwise, a receiver is out of order possible!

5. Upon completion of the update, the receiver will restart and turn on in the "Setup Wizard" mode.

6. In the first step, "Wizard Settings" you will be prompted to select the language of the menu and the operator. You must select the "tricolor TV center", only after that you can go to the next step.

7. After the search for the TV and radio channels "Tricolor TV", you must make sure that the receiver version has changed to 1.1.001 . To do this go to « Menu »-\u003e « Dreinfo "-\u003e" Status "and check the value in the third line. If the receiver software version has not changed, you need to turn off and enable the receiver on the TV channel "Infocanal Tricolor TV" and repeat the update procedure.

8. This update on the receiver and the module is completed, your receiver is ready for further work.

You can view the Educational Roller on the software update you can watch the TV channel "Teleinstructor" and in the "Video Instructions" section on the Tricolor TV website.

Description of the new version of:

A new software is intended to increase the level of protection of receiving equipment and ensure the stability of its work, as well as make it operation when watching TV channels and using additional services "Tricolor TV" more convenient.

The software added a new feature in the Package Interface "Tricolor TV" package. Some buttons received additional functionsFor example, pressing a red button Calls a description of the selected movie, green - options for sorting a movie list (according to the alphabet, by genres, according to the closest sessions, on the novelty of the schedule), yellow - a list of films to which the timer was installed, blue - list Films that will be available to view the next time you update the repertoire.

For the convenience of subscribers, the "Status" menu has been recycled. After updating, the subscriber will be available two options for displaying information:

Brief (contains the most frequently used data, including information about the ID number) - is displayed when switching to the menu item "Status";

Advanced (contains all information about the receiver) - is called by pressing the red button ("F1" or "I") on the remote control during the status menu.

Frequently asked Questions:

Question: What is necessary to update the software?

Answer:In the new software version of the GS8305 and GS8306 receivers, a new, more convenient interface of the "Tricolor TV cinema hall" package has been reworked by the status menu, as well as changes in system settings receiver, which increases the stability of his work.

Question: Why did the status information window become different? Where did some items that were before?

Answer:For the convenience of subscribers, the "Status" menu has been recycled. Now you are available two options for displaying information: brief (contains the most frequently used data, including information about the ID number) and advanced (contains all information about the receiver).

Question: Why changed function buttons in the interface of the package "Tricolor TV" package?

Answer: The new software version was implemented additional features Package interface "Cinema Tricolor TV". Now, by pressing the red button, you can read the description of the selected movie, green - choose one of possible options Sorting a list of films (Alphabetically, by genre, according to the nearest sessions, on the novelty in the schedule), Yellowy - see a list of films to which the timer was installed, blue - see a list of movies that will be available for viewing when the repertoire of the Package "Tricolor TV". Also, in the new version of the software, the possibility of outputting the "Tricolor TV cinema" package interface screen when you click on the "Order Movie" or "Split File" button when watching / listening to any television or radio channel, and not just how it was before When watching TV channel TV channel.

To view HDTV television channels, " Tricolor"Consisters satellite receiver Tricolor TV HD GS-8306.. With this satellite receiver, it is possible to watch television channels as in SD quality (standard resolution) and HD quality (high-definition television - HDTV) - HD maximum package. This model supports the completed set of services required when viewing the channels of both standards. Satellite HD Receiver can be connected to a variety of types of TVs and displays. In this small description, we will present how to connect GS 8306.without resorting to help professional.

You can always buy a set of tricolor TV in Murmansk, or receiver separately, get a free consultation, in our office, calling by phone in Murmansk 750-335 or 236-335 . By purchasing the equipment Tricolor TV, you have the opportunity to look at your LCD TV 10-ki channels in magnificent quality - HDTV (high definition format). More comprehensive information about the equipment "Tricolor TV Full HD" you have the opportunity to get on our website \u003e\u003e\u003e.

In the equipment set Tricolor TV HD. - To view HDTV channels - Tricolor TV Full HD, together with the receiver, satellite antenna and the converter, is included in addition, the cost of a one-year subscription to the "Tricolor Maximum HD" package, and after a year of viewing, subscriber. The fee will be only 900 rubles. IN this moment Package Tricolor Maximum HD includes 25 channels in HD quality and more than 100 channels in SD quality, packets are constantly updated with new TV channels.

With 1 point on the receiver GENERAL SATELLITE. GS-8306. We can mark its modest dimensions. Its sizes are only 250x180x44 mm. Rounded corners, silver or black housing, in this case the question is formed: how in this small, but cute to the view of the device can be placed satellite television?

On the external panel of the GS-8306 satellite receiver, there are 5 buttons: one inclusion key and 2nd - to switch the body and radio channels and change the volume of the volume, respectively, and in addition the function indicator. From the side is a slot of the map address. On the rear panel - optimized connectors configuration for connecting to audio / video techniques.

The rear panel GS 8306 consists of:

Input for connecting a coaxial cable from satellite plates - LNB in
- LNB OUT output (loop output), to connect the next receiver by chain
- RCA-inputs and outputs ("bells")
- HDMI Exit is the newest digital multimedia interface
- USB port connector for flashing satellite receiver
- Jack connector for connecting power adapter

The 1st acquaintance occurred. Let's connect!

The HD tricolor kit needed to view HDTV channels is included in addition satellite dish and circular polarization converter (LNB) for receiving a signal from the EutelSat 36 A / B satellite. The plate must be configured to the desired satellite, for the central part of Russia, this is the EutelSat 36 A / B 36 ° C satellite. d.

The satellite converter is connected to the input of the satellite HD receiver - LNB in \u200b\u200bby the coaxial cable. To catch satellite signal high quality in coaxial cable There should be no damage and length should not exceed 100 meters.

Now connect to receiving TV. It is possible to do or via RCA outputs ("tulips"), or using an HDMI cable. In the event that you have a widescreen TV, to view HD channels, on modern flat-panel TVs, the optimum solution will be to connect the receiver of the HDMI cable.

Scan TV channels

During the 1st inclusion of the HD GS 8306 satellite receiver or after resetting it to the factory settings, the "Wizard of the first installation" will be launched. The process of scanning the TV channels is made up of 3 unearth stages:
1 Stage: You need to choose the language of the menu: Russian, Ukrainian or English
Stage 2: Region Choice
3 Stage: Scanning Channels Tricolor TV. The setup wizard initializes this mode after the region is directed. The scanning of the TV channels takes no more than one minute, after which the satellite receiver switches to the view mode. The numbering of the body and radio channels in the lists begins with a zero channel. "Zero" line in the TV list occupies "Infocanal Tricolor TV". Then there are HD channels of the Maximum HD package, followed by the "Basic" package channels, etc. At any time it is possible to configure the favorite list of tricolor TV channels by organizing them on only to you to groups!

Note! Installing the satellite plate will require maximum dilution. When incorrect installation satellite antenna There may be faults in the work or exit of equipment in order by factors that do not depend on the equipment seller. In case you are not fully confident that you will be able to mount the equipment yourself.

You can always order in our company (Tel.: 750335,236335) The installation and configuration service of the satellite antenna as in Murmansk and in the Murmansk region.

class \u003d "Eliadunit"\u003e

You can update the software yourself. This is done quite simply, if you follow the tricolor instruction proposed by the provider.

Instructions for updating the tricolor GS 8305 and GS 8306

To update the receiver software, you must perform the following actions:

  1. Remove the receiver power cord from the outlet, then turn on the receiver to the network again. It is necessary for a complete reboot.
  2. Switch the receiver to the "Infocanal Tricolor TV" channel. After a couple of seconds, a message appears on the TV screen on the need to update the receiver software, the message will be in the body: Update Software? And answer options: yes and no, you should click on "yes."

If this message does not appear on the TV screen, this message appears on the need to update the software, subscribers need to reset the receiver settings to the factory:

  • you need to go to the "Menu" of the receiver;
  • go to the option "Settings";
  • select from the list "Factory settings";
  • press "OK" on the console.

After receiving the consent to the update, the screen will begin to appear on the process of updating the receiver software.

Software updates takes an average of five minutes.

When the update is completed, the receiver will restart and turn on in mode "Setup Wizard".

At the initial stage "Wizard Settings"subscribers will be prompted to select the menu language and provider. Need to choose from the list "Tricolor TV Center"After that, you can proceed to the next step. When the search for the body and radio channels "Tricolor TV" is completed, it will be necessary to make sure that the receiver software version has changed by 1.1.001. To do this, you need to go through a few steps:

class \u003d "Eliadunit"\u003e

  • go to "Menu";
  • go to "Dreinfo";
  • next - "Status";
  • after transition, check the software value in the third line.

If the version of the receiver software has not changed (you need to verify with the old, which is obviously recorded on the leaflet), the subscribers need to turn off and turn on the receiver to the TV channel "Infocanal" Tricolor TV "and repeat the update procedure first.

Description of the new software

New software is designed to increase the level of reserved protection and ensuring the stability of its work. Also, a new one is able to operate the receiver when watching TV channels and the use of additional services "Tricolor TV" is more convenient. New software has been added to new features in the Tricolor TV cinema hall package interface. Separate buttons also received additional new features, for example:

  • by pressing the red button, you can call a description of the selected movie;
  • pressing green - options for sorting the list of films (by genres, alphabet, closest sessions, novelty in schedule);
  • pressing yellow - a list of films will appear to which the subscriber has set the timer;
  • pressing blue - the list of films will be displayed to view the next time you update the repertoire.

The "Status" menu was also recycled for more convenient use. After the update, the subscriber will receive access to two information display options: a brief option contains the most frequently used data, including information about the receiver ID number. It is displayed immediately when switching to the option in the "Status" menu;

advanced contains all information about the receiver - opens after pressing the red button ("F1" or "I") on the remote remote control When in the "Status" menu.

Why update the receiver software?

Tricolor TV constantly releases updates for software. To keep abreast of all new products, more comfortable and high-quality, you need to track them on the official website of the company, in order to CI the module did not give failures. This procedure does not take much time and is completely free for registered users.

Ci is a built-in module, software is necessary for safe and high-quality channel translations.

Another reason for tracking new software is that the user will not be able to configure the module software if necessary, if you missed one, or several previous versions.

Stable work the largest operator satellite television Tricolor TV becomes possible only after works correct installation and subsequent configuration of components. This process It can be done by the user independently, it is enough to explore the current instruction in 2019. Considering how to configure the tricolor TV receiver independently select positive qualities from the use of user search and availability different generations Models technical devicesThe principle of working with which may vary.

In this material we will look at:

  • configuration features;
  • differences with different device models.

Preliminary actions and features of manual search channels

Connecting the receiver is identically produced for all types of receivers. It is first necessary to install a satellite plate, according to official coordinates for your region, which are offered by the operator. Set the correct tilt angle and swipe the cable to the receiver.

Classically, there are several ways to connect:

  • the high-frequency connection can be connected using the appropriate antenna cable;
  • the low-frequency signal is received and transmitted using a classic SKAnt type cable.

By connecting the wiring and making sure in stable operation, you can proceed to further registration and search. If the device functions incorrectly, you can try independently search for the necessary information in the appropriate technical section of the official website or contact the support service specialist. You can do it by free Number, Or using the feature of additional software.

How to configure tricolor TV channels on your own on receiver GS 8306

GS 8306 is a popular model among telecommunication operator clients capable of displaying an image in HD quality on the screen. The Smart card here is installed in a separate connector, which expands the use of the device.

The configuration is made by a classic way:

  1. Open the Settings menu;
  2. Select Section "Search", click on the "Manual" item;
  3. Fill out the proposed field by entering operating frequencies;
  4. Repeat the required number of times until all channels are added to the database;
  5. Save the changes and restart the device.

Manual search has a positive effect on the following factors:

  • good quality of the translated image when proper installation satellite;
  • increased reception speed and data packets.

Self setting parameters takes more time and requires a search. for more information. List of frequencies and other parameters are located in the technical section of the official website.

How to configure the receiver DRS 5001 tricolor TV yourself

Though specifications DRS 5001 and inferior to some modern counterparts, this device All the same uses active demand among customers. The timely release of software updates contributes to the introduction of relevant software featuresWhat does it talk about high quality Service and individual approach to each client.

Considering how to configure the tricolor receiver, it is necessary to pre-note the identity of the connection of technical equipment, which indicates a similar principle of functioning. This configuration implies:

  • registration of the receiver on the website or in the Personal Account;
  • satellite synchronization and channel search.

Registration is a mandatory action for all clients of the telecommunications operator. To do this, it is enough to enter a smart card ID control panel in the corresponding field, consisting of a combination of 12 or 14 characters. Additionally, specify the receiver number and personal contact details.

If everything is performed correctly, information about technical components and personal data will be added to the protected base, after which you can configure the channels for everyday viewing.

Configuring the receiver GS B520 tricolor TV

GS B520 is a new generation of equipment provided by the operator. Become the owner of this technical solution Maybe each company's client, taking part in the program to replace outdated technical components.

The main advantages of the modern console can be attributed:

  • the ability to broadcast flow to mobile devices;
  • connect K. home network Wi-Fi for data exchange;
  • a complete set of modern ports - USB, Ethernet, HDMI and others;
  • interface for connecting the drive with the subsequent ability to recording the broadcast;
  • access to "Cinemaings", "Games" and other unique offers from Tricolor TV.

Preparation for use is made in the usual way: by connecting to satellite platesThe user needs to register a device in a common database. Channel settings can be both automatically and manual mode. Using custom parameters will allow you to solve channels yourself and simplify access to them. Do not forget to save changes Before rebooting the device: Incorrect data execution Action can contribute to software malfunction.

How to set up the receiver gs b211 tricolor tv yourself

Configuring the tricolor TV receiver independently for the GS B211 technical equipment model is made similar to the above method. The modern device allows you to translate a high-quality signal with the ability to duplicate it to other devices. Detailed technical information And help on the question of interest can be obtained on the official website of the operator.